29
Special Features
To change the receive mode, repeatedly
press
MODE
. The receive mode changes as
follows:
ã)
ã)
ã)
ã)
— accesses the AM mode
")
")
")
")
— accesses the FM mode
)+
)+
)+
)+
— accesses the FM Mode, Motorola
Trunking System (with a 4- or 5-digit ID
code)
!
!
!
!
— accesses the FM Mode, EDACS
Trunking System (with 4-digit decimal ID
code or 5-digit AFS code)
Note: MO (MOT) and ED modes are not
available when the scanner tunes up or
down through the frequency ranges in which
the trunking operation is not used.
USING THE ATTENUATOR
To reduce interference or noise caused by
strong signals, you can reduce the scanner's
sensitivity to these signals.
There are two attenuator modes in your
scanner. In normal attenuator mode, you set
the attenuator in each channel or each band/
group in the search and tune mode. In global
mode, you set the attenuator only once. The
global setting affects every mode.
Press
ATT
to turn on or off the attenuator
while the channel number is indicated, or
while the scanner is searching through
bands/groups. When the attenuator is on,
ã
ã
ã
ã
appears at the seventh digit in the top line.
When you turn it off,
ã
ã
ã
ã
changes to "
ôôôô
". You
cannot set the attenuator while the scanner
is scanning.
Press
FUNC
then
ATT
to set the attenuator to
the global mode.
#CF98Cý ã00ô
#CF98Cý ã00ô
#CF98Cý ã00ô
#CF98Cý ã00ô
appears for 2
seconds at the bottom line and
Wý
WýWý
Wý
(on) or
####
(off) appears. Press
ATT
to turn on or off the
attenuator.
ã00FE
ã00FE
ã00FE
ã00FE
or
ã00V
ã00V
ã00V
ã00Vý
appears on the
bottom line while scanning.
Press
FUNC
then
ATT
again to turn off the
global attenuation mode.
*FID8Cýã00
*FID8Cýã00
*FID8Cýã00
*FID8Cýã00
is indi-
cated at the bottom line for 2 seconds.
Note: If you turn on the attenuator, the scan-
ner might not receive weak signals.
TURNING THE KEY TONE ON
AND OFF
Each time you press any of the scanner's
keys, the scanner sounds a tone. To turn the
scanner's key tone off or on:
1. If the scanner is on, turn
VOLUME OFF/
MAX
counterclockwise until it clicks to
turn the scanner off.
2. Turn
VOLUME OFF/MAX
clockwise to
turn the scanner on.
3<C:FD<ý 0Fý L8C
3<C:FD<ý 0Fý L8C
3<C:FD<ý 0Fý L8C
3<C:FD<ý 0Fý L8C
0ILEB@E>
0ILEB@E>
0ILEB@E>
0ILEB@E>
appears.
3. While
3<C:FD<ý 0Fý L8Cý 0ILEB@E>
3<C:FD<ý 0Fý L8Cý 0ILEB@E>
3<C:FD<ý 0Fý L8Cý 0ILEB@E>
3<C:FD<ý 0Fý L8Cý 0ILEB@E>
appears, press
1
to turn on the key tone
or
2
to turn it off.
CHANGING THE DISPLAY
CONTRAST
1. Press
MAN
.
2. Press
FUNC
then
9
.
1J<ý 1Gó FNEý B<PJ
1J<ý 1Gó FNEý B<PJ
1J<ý 1Gó FNEý B<PJ
1J<ý 1Gó FNEý B<PJ
KFýJ<Ký:FEKI8JKô
KFýJ<Ký:FEKI8JKô
KFýJ<Ký:FEKI8JKô
KFýJ<Ký:FEKI8JKô
appears.
3. Press
8
8
8
8
or
9
9
9
9
to select the contrast.
4. Press
ENTER
to set the display contrast.
CLONING PROGRAMMED
DATA
You can transfer programmed data to and
from another RadioShack PRO-2053 or a
PRO-93 scanner using an optional connect-
ing cable with
1
/
8
-inch phone plugs on both
ends, (not included) available at your local
RadioShack store.
Follow these steps to clone the data.
Summary of Contents for 20-466
Page 54: ...54 Notes Notes...
Page 55: ...55 Notes...
