background image

Setting Home ID

 

Home ID data allows you to enter the ID number that will appear on receiver radio as you 
communicate with them. User can select Home ID number 1-16.  
 
1. Set the Transmitter and Receiver in the same channel (and same quiet code, if you select one) 
 
2.   Hold down the Receiver’s 

FUNC 

key and press 

CALL

 key to enter Setting Home ID mode. 

Release all key and then press 

UP

 or 

DOWN

 key to select your desired Home ID number. 

 
3. Press 

PTT

 key to stored the setting.  

 

Note: 

• 

If no key  pressed  within 20 seconds in Setting Home ID mode, the radio will 
automatically exit without saving. 

• 

If Home ID is changed, the radio will automatically reset the Caller ID number to Group 
Call.

 

 

Setting Caller ID 

Caller ID data allows you to enter the receiver’ radio ID number that you want to call. Receiver’s 
radio only receive the Call when the Caller ID data is matched with it Home ID. User can select 
Caller ID number 1-16 or Group Call. 
 
1. Hold down Transmitter’s 

CALL

 key until the  Call

 

ID number flashes on the display, press 

UP

 or 

DOWN 

key to  select the receiver’s home ID number or GROUP option. (If you select receiver’s 

home ID number 1 ~ 16, you can only send a page  to  one user or several users setting with the 
same ID home number, if you select GROUP option, you can send a page to all users.).  
 
2. Press 

PTT

 key to stored the setting. 

 

Note: 

• 

If user presses UP or DOWN key to change Caller ID number and the number is equal 
to the Home ID. Then the LCD will display the next Caller ID number in order to prevent 
any match of Home ID and Caller ID. 

 

Call Melody

 

In Transmitter’s radio, the call melody will generate after the Call ID data is sent. The Call melody 
is depends on the Call ID number. The Call tone melody map is state as following Table. 

Call Melody No. 

ID 

Call ID = 

Group Call 

Call ID = 

1~4 

Call ID = 

5~8 

Call ID = 

9~12 

Call ID = 

13~16 

 
In Receiver’s radio, the call melody will generate after the Call ID data is received. The Call 
melody is depends on the Sender ID number. The Call tone melody map is state as following 
Table. 

Call Melody No. 

ID 

Group Call 

Sender ID = 

1~4 

Sender ID = 

5~8 

Sender ID  

= 9~12 

Sender ID  

= 13~16 

 

 
 
 
 
 

Summary of Contents for 21-1905














Reviews: