background image

15

Specifications

ˆ

Specifications

Input Sensitivity/Impedance

DJ MIC (XLR jack)  .............................................................  1.5 mV, 600 ohms, Balanced/Unbalanced
AUX MIC (Phone jack)  .......................................................................  1.5 mV, 600 ohms, Unbalanced
Phono .........................................................................................................................  3 mV/50 kOhms
Line ........................................................................................................................  150 mV/27 kOhms

Output Level

Main Out .........................................................................................................................  2V/10 kOhms
Record ....................................................................................................................  150 mV/10 kOhms
Send .......................................................................................................................  150 mV/10 kOhms
Frequency Response  ................................................................................................ 20–20k Hz ±3 dB

S/N Ratio

Mic ...............................................................................................................................................  55 dB
Phono .......................................................................................................................................... 65 dB
Line .............................................................................................................................................  75 dB

Distortion

Mic ..............................................................................................................................................  0.20%
Phono .........................................................................................................................................  0.08%
Line ............................................................................................................................................  0.05%

Tone Control, DJ MIC, AUX, CH 1, CH 2, CH 3, CH4

HIGH Boost/Cut Range  ..............................................................................................  ±10dB at Center
MID Boost/Cut Range  ................................................................................................  ±10dB at Center
BASS Boost/Cut Range  .............................................................................................  ±10dB at Center
ECHO Delay Time ..............................................................................................................  50 –120ms
TALKOVER Attenuation  ...................................................................................................  –8 to –38 dB

Power Source ......................................................................................................... AC 120V, 60Hz, 20 Watt

Power Fuse  .....................................................................................................................  0.5 Amp/250 Volts 

Dimensions (HWD)....................................................................................................  4 

7

/

16

 

×

 19 

×

 11 Inches 

(113 

×

 482 

×

 280 mm)

Weight .........................................................................................................................................  11 Ibs 6 oz 

(5.15 kg)

Specifications are typical; individual units might vary. Specifications are subject to change and improve-
ment without notice.

You are getting a hum from other 
input source

Make sure there are no low-level inputs connected to the LINE input 
jacks.

You are getting feedback noise.

Move the microphone further away from the output speakers or use 
a unidirectional microphone.

Problem

Possible Solution

32-3008.fm  Page 15  Thursday, April 6, 2000  4:03 PM

Summary of Contents for 32-3008

















Reviews: