background image

5

16. 

Never push objects of any kind into this appliance through openings, as they 

may touch dangerous voltage points or short out parts that could result in a fire 

or electric shock. Never spill liquid of any kind on the appliance.

17.

 Move appliance and cart combinations with care. Quick stops, excessive 

force, and uneven surfaces may cause the appliance and cart combination to 

overturn.

18. 

Unplug this appliance from the wall outlet and refer servicing to a qualified 

service personnel under the following conditions:

•   When the power-supply cord or plug is damaged.
•   If liquid has been spilled or objects have fallen into the appliance.
•   If the appliance has been exposed to rain or water.
•   If the appliance does not operate normally by following the operating 

instructions. Adjust only those controls that are covered by the operating 
instructions, as an improper adjustment of other controls may result in 
damage and will often require extensive work by a qualified technician to 
restore the appliance to normal operation.

•   If the appliance has been dropped or damaged in any way.
•   When the appliance exhibits a distinct change in performance.

19

. Do not attempt to service this appliance yourself, as opening or removing 

covers may expose you to dangerous voltage or other hazards. Refer all 

servicing to qualified service personnel.

20. 

When replacement parts are required, be sure the service technician has 

used replacement parts specified by the manufacturer or have the same 

characteristics as the original part. Unauthorized substitutions may result in fire, 

electric shock, or other hazards.

21. 

Upon completion of any service or repairs to this appliance, ask the service 

technician to perform safety checks to determine that the appliance is in proper 

operating condition.

22.

 For added protection for this product during a lightning storm, unplug it from 

the wall outlet. This will prevent damage to the product due to lightning and 

power line surges.

23.

 Only use attachments recommended by the product manufacturer.

24. 

The product should be mounted to a wall or ceiling only as recommended by 

the manufacturer.

25.

 Do not overload wall outlets, extension cords, or integral convenience 

receptacles, as this can result in a risk of fire or electric shock.

Summary of Contents for 3200026

























Reviews: