Radio Shack 4-Way Electronic Crossover Owner'S Manual Download | Manualshive

Page: 7 / 8

background image

7

• noise/spike suppressors to control igni-

tion coil, distributor, alternator, or genera-
tor noise, as well as to eliminate pops and
clicks

• ground loop isolator

Replacing the Fuse

This crossover uses a 1-amp, blade-type fuse
for protection from power surges or a short cir-
cuit. If the POWER indicator turns off or does
not turn on, replace the fuse with a new one of
the same size and type.

1. Be sure the power source is off.

2. Firmly grasp the fuse's plastic end and

pull it out.

3. Holding the new fuse's plastic end, push

it firmly into place.

SPECIFICATIONS

Frequency Response ................................................................................................................. 10 Hz–40 kHz

Channel Separation at 1 kHz .................................................................................................................. 50 dB

Distortion at 1 kHz and 1 Volt ................................................................................................................... 0.1%

S/N Ratio ................................................................................................................................................. 70 dB

Crossover Slope ......................................................................................................................... 18 dB/Octave

Power Requirements ............................................................................................. 12V DC (Negative Ground)

Dimensions (HWD) ................................................................................................... 8.27

×

6.30

×

1.22 Inches

(210

×

160

×

31 mm)

Specifications are typical; individual units may vary. Specifications are subject to change and improvement
without notice.

Blade-Type Fuse

12-2020.fm Page 7 Tuesday, May 23, 2000 6:56 PM

«
...
5
6
7
8
»

Summary of Contents for 4-Way Electronic Crossover









Reviews:

No comments

Related manuals for 4-Way Electronic Crossover

DXP-6 Competition

Brand: HELIX Pages: 12

Brand: Rane Pages: 11

Brand: EAW Pages: 12

Brand: Ashly Pages: 2

Brand: LEM Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands