©2006.
RadioShack
Corporation.
All rights reserved.
RadioShack
and
RadioShack.com
are trademarks
used by
RadioShack
Corporation.
43-3911
10A06
Printed in China
When using your telephone equipment, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons,
including the following:
• Do not use this product near water, for example,
near a bathtub, washbowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless
type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the
vicinity of the leak.
• Use only the batteries indicated in this manual. Do
not dispose of batteries in a fire. They may explode.
Check with local codes for possible special disposal
instructions.
important safety instructions
Your phone complies with Part 68 of
FCC Rules
. You must, upon
receipt, provide the FCC registration number and the REN to your
telephone company. Both numbers are on the bottom of the phone.
Note: You must not connect your phone to:
• coin-operated systems
• most electronic key telephone systems
• party-line systems
Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission, or
corporation commission for information.
We have designed your phone to conform to federal regulations,
and you can connect it to most telephone lines. However, each
phone (and each device, such as a telephone or answering machine)
that you connect to the telephone line draws power from the
telephone line. We refer to this power draw as the device’s ringer
equivalence number, or REN on the bottom of your phone.
If you use more than one phone or other device on the line, add up
all of the RENs. If the total is more than five (three in rural areas),
your telephones might not ring. If ringer operation is impaired,
remove a device from the line.
In the unlikely event that your phone causes problems on the phone
line, the phone company can temporarily discontinue your service.
If this happens, the phone company attempts to notify you as soon
as possible and advises you of your right to file a complaint with the
FCC.
Also, the phone company can make changes to its lines, equipment,
operations, or procedures that could affect the operation of this
telephone. The telephone company notifies you of these changes in
advance, so you can take the necessary steps to prevent interruption
of your telephone service.
surge protection
Your telephone has built-in protection circuits to reduce the risk of
damage from surges in telephone line and power line current. These
protection circuits meet or exceed the FCC requirements. However,
lightning striking the telephone or power lines can damage your
telephone.
Lightning damage is not common. Nevertheless, if you live in an
area that has severe electrical storms, we suggest that you unplug
your phone when storms approach to reduce the possibility of
damage.
FCC statement
This product is warranted by
RadioShack
against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase from
RadioShack
company-owned stores and authorized
RadioShack
franchisees
and dealers. For complete warranty details and exclusions, check with your local
RadioShack
store.
RadioShack
Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
04/04
limited one-year warranty
• Keep your phone dry; if it gets wet, wipe it dry
immediately.
• Use and store your phone only in room
temperature environments. Handle your phone
carefully; do not drop it.
• Keep your phone away from dust and dirt, and
wipe it with a damp cloth occasionally to keep it
looking new.
• Modifying or tampering with your phone’s
internal components can cause a malfunction
and might invalidate its warranty. If your phone is
not performing as it should, take it to your local
RadioShack
store for assistance.
care and service
You can store up to 20 of your most frequently dialed
phone numbers, and dial the number by using one of
your memory locations (M1-M10 or 0-9).
storing numbers in memory locations
1. Press
STORE.
2. Enter the phone number you want to store, including
1+ area code for long distance numbers.
3. Press any of the
M1-M10 memory buttons. To store
the number to an indirect memory location, press
MEM and then press any key between 0 and 9.
4. Use the supplied index cards to record stored
numbers.
• You can store up to 16 digits for each number.
• If you make a mistake while entering the number,
press
STORE
twice, and then re-enter the phone
number.
• To change a number in memory, store a new one
in its place.
entering a pause in a memory number
In some telephone systems, you must dial an access
code (9, for example), wait for the second dial tone, and
then dial the number.
Press
OPT/P to enter a three-second pause. For a long
pause, press OPT/P again. Each time you do this, one
digit of memory is being saved.
Note
: For more information about
OPT
/
P
, refer to the section
“using
OPT
/
P
.”
dialing a memory number
Press the desired location number (
M1-M10). To dial a
number stored in the indirect memory location, press
MEM and the location number (0-9).
chain dialing
You can make a call using more than one of the phone’s
memory locations. Chain dialing is useful for dialing
special services, such as alternate long distance or
bank-by-phone.
testing stored emergency numbers
If you want to test a stored emergency number (police
department, fire department, ambulance), make the
test call during the late evening or early morning hours
to avoid peak demand periods. Remain on the line to
explain the reason for your call.
memory dialing
NOTES
If you subscribe to Caller ID service, the phone
company sends information about the call between the
first and second rings of every call you receive. The
phone can also show the name of the caller if you have
that service.
If the Caller...
Display Reads
Left a message
MSG
Called more than once
REPEAT
Blocks their number or name
PRIVATE
Is not within a Caller ID area
OUT OF AREA
Is calling long distance
LONG DISTANCE
Note
: If the Caller ID record is garbled,
��NE ERROR
��NE ERROR
appears.
reviewing caller ID records
Each time you receive a call, your phone stores a Caller
ID record that you can review later. The record includes
the following:
• Call number (1, 2, 3, etc.)
• Caller’s phone number
• Time and date of the call
• Caller’s name (if you have this service)
Repeatedly press REVIEW
or
to see Caller ID
records. -END OF LIST-
END OF LIST--
appears after the first or last
Caller ID record as you scroll through the list.
• Your display can show up to 11 digits of a phone
number. If the number is longer, the display
shows only the last 11 digits.
• The phone returns to the time/date display after
about 20 seconds, if you do not press a key.
deleting caller ID records
You can delete individual Caller ID records, or delete all
of them after you review them. You cannot delete Caller
ID records that have not been reviewed or during a call.
• To remove a single Caller ID record, press DELETE
twice.
• To remove multiple records, hold down DELETE until
DELETE ALL? appears. Then, press DELETE once.
No CALLS appears in the display.
• If you have unread records while holding DELETE, xx
NEW CALLS and PLEASE READ display alternately.
Review the records first before deletion.
using OPT/P
Your phone provides dialing options for different
phone systems, allow you to select the correct dialing
selection for a phone number before you press
CALLBACK.
1. Repeatedly press REVIEW
or
to find the
desired phone number.
2. Repeatedly press OPT/P to select the desired dialing
option. You can select one of the following:
• seven-digit number
• 10-digit number (area code + number)
• 11-digit number (1+ area code + number)
using callback
Press
CALLBACK to automatically dial the number
displayed in the Caller ID display.
caller ID operation
NOTES
No dial tone — Be sure the handset and phone line
cords are securely connected.
Display is blank — Be sure batteries are correctly
installed.
Volume drops or sound is distorted — Be sure any
— Be sure any
other phones are not being used.
Call is noisy — Check to see if the cords are securely
connected.
Can receive calls, but cannot make calls — Set
— Set MODE
to the correct dialing mode, P or T.
No Caller ID information appears — You have not
subscribed to Caller ID service with your phone
company.
troubleshooting
Switch MODE T/P/TB to T or P to match the type of
service you have. If you are not sure which service
you have, do this simple test.
1. Set MODE to T.
2. Lift the handset to press SPEAKER and listen for the
dial tone.
3. Press any number other than 0.
• If your dial tone stops, you have touch-tone service.
Leave MODE to T.
• If the dial tone continues, you have pulse service.
Set MODE to P.
NOTE
: TB is designated for use in the UK.
using tone services on a pulse line
I
f you have a pulse line, you might need to use tone
service for special services, such as bank-by-phone. To
use tone service, do the following:
1. Be sure MODE is set to P and dial the number.
2. When the system answers, press
. Any additional
numbers you press will send a tone signal.
After you hang up, your phone automatically resets to
pulse dialing.
setting the dialing mode
43-3911 rscn.indd 2
10/12/2006 11:30:02
