background image

3.  To set the playing time for 59 minutes, release SLEEP.  The radio 
    automatically turns off after 59 minutes. 
 
    To set the playing time for less than 59 minutes, hold down the SLEEP 
    button.. 
 
4.  Release SLEEP. 
 
CASSETTE OPERATION 
 
You can play a cassette, record from the radio, or make the live 
recordings. 
 
LOADING A CASSETTE TAPE 
 
Follow these steps to load a cassette tape. 
 
1.  Use your finger or a pencil to turn the cassette's hub and take up 
    any tape slack. 
 
2.  Press STOP/EJECT to open the cassette compartment door. 
 
3.  Load the cassette with its open edge up and the full reel to the 
    right. The side facing you is the side that plays. 
 
4.  Close the cassette compartment door. 
 
PLAYING A CASSETTE TAPE 
 
Load a cassette as described in "Loading a Cassette Tape."  Then follow 
these steps to play the tape. 
 
Warning:  To protect your hearing, set VOLUME near its lowest setting 
          before you turn on the tape player. 
 
1.  Press RADIO ON. 
 
2.  Set the function selector to TAPE. 
 
3.  Press PLAY. 
 
4.  Adjust VOLUME for a comfortable listening level. 
 
5.  Adjust BALANCE and TONE for optimum sound. 
 
    To rewind or fast-forward the tape, press REWIND or FAST-F.  Press 

Summary of Contents for Chronosette-276

















Reviews: