35
Trunking Operation
6. Press
ENTER
for each entry. If you make
a mistake, press
CLEAR
and enter the
correct size code.
Notes:
• The default setting of the bank is for
Motorola Type II. However, if you set
Type I and you want to return to Type
II, enter 15 at Step 5.
• To confirm the input, repeat Steps 1–
5 and press
ENTER
. Each time you
press
ENTER
, you confirm the size
code. If you find an error, press
CLEAR
and begin again at Step 1.
7. Press
SCAN
to start scanning.
Talk Group IDs
There are 10 talk group ID banks and each
ID bank has 5 sub-banks. Each sub-bank
has 20 ID locations. You can program up to
100 talk group IDs in each bank, so you can
program up to 1,000 talk group IDs in 10
banks. When the scanner stops on a trans-
mission in the Motorola, or EDACS mode, it
checks to see if the ID has been stored. In
the closed mode, the scanner only stops on
the transmission and displays its text tag if
you have stored and not locked out the ID. In
the open mode, the scanner always stops on
a transmission, but it displays the ID's text
tag if you have stored the ID.
Storing Talk Group IDs
To store a talk group ID, press
TRUNK
when
the scanner stops on a voice channel trans-
mission or when a talk group ID is indicated
in the manual mode.
The bottom line indicates where the ID was
entered as
% ý J8M<ý 4
% ý J8M<ý 4
% ý J8M<ý 4
% ý J8M<ý 4V4
V4
V4
V44
4
4
4
and then changes
to
ýýýý
% û4444
% û4444
% û4444
% û4444
. The first X in
% ýJ8M<ý4V44
% ýJ8M<ý4V44
% ýJ8M<ý4V44
% ýJ8M<ý4V44
is the
sub-bank number (0–4) in the bank. XX is
the position number of the ID (00–19) in each
sub-bank.
If you press
TRUNK
and the ID is already
stored,
% ýN8JýJ8M<;
% ýN8JýJ8M<;
% ýN8JýJ8M<;
% ýN8JýJ8M<;
appears.
Note:
When you try to store more than 100
talk group IDs in a bank,
)<DFIPý =LCCü
)<DFIPý =LCCü
)<DFIPý =LCCü
)<DFIPý =LCCü
ap-
pears. Clear some talk group IDs in order to
store new ones (see “Clearing Talk Group
IDs” on Page 37).
Follow these steps to manually store talk
group IDs or to edit a stored ID.
1. Press
PROG
.
2. Press
TRUNK
.
3. To select the bank where you want to
store the ID, repeatedly press
FUNC
then
8
8
8
8
or
9
9
9
9
until you reach the
desired bank.
4. Press
TRUNK
repeatedly to select the
sub-bank.
5. Press
8
8
8
8
or
9
9
9
9
to select the location
where you desire to store the ID num-
ber.
7
S0
S4
S0
S4
S0
—
—
—
Block
Size Code
9
10
11
12
13
14
15
16
8Wdaý&#&
8Wdaý&#&
8Wdaý&#&
8Wdaý&#&
ED
ED
ED
ED
?:ýD
?:ýD
?:ýD
?:ýDe$
e$e$
e$ý&&
ý&&
ý&&
ý&&
CEJ0ýded[
CEJ0ýded[
CEJ0ýded[
CEJ0ýded[
First ID location
Summary of Contents for PRO-2053
Page 54: ...54 Notes ˆ Notes ...
Page 55: ...55 Notes ...
