background image

 

 

20-428 Owner’s Manual 

 

Page 40 of 50   

1. Press PROG then TRUNK. 
 
2. For each bank you want to program, repeatedly press FUNC. Then /¥ or ¥/ to select the bank. 
 
3. Press FUNC. Then press 8. Size Code Setting appears. 
 
4. Enter the size code supplied with the Type I system information, referring to the instruction that 
appears on the display. If the information was not supplied, try the following common fleet maps. 
 
Block 

   Size 

Code 

  1 2 3 4 5 6 7 8 
0  S11 S4 S4 S12 S4 S3 S10 S1 
1  S11 S4 S4 –  S4 S10 S10 S1 
2  S11 S4 S4 S4 S12 S4 S11 S2 
3  S11 S4 S4 S4 –  S4 S4 S2 
4  S11 S4 S4 S4 S4 S12 S4 S3 
5  S11 S4 S4 S4 S4 –  S4 S3 
6  S11 S4 S12 S4 S4 S12 S4 S4 
7  S11 S4 –  S4 S4 –  S4 S4 
 
Block 

   Size 

Code 

  9  10 11 12 13 14 15 16 
0  S4 S0 S4 S0 S3 S4 S4 S3 
1  S4 S0 S0 S0 S3 S3 S4 S10 
2  S0 S0 S0 S0 S11 S10 S4 S10 
3  S0 S0 S0 S0 S4 S4 S11 S11 
4  S0 S0 S0 S0 S4 S4 S11 S0 
5  S0 S0 S0 S0 S0 S4 S0 S0 
6  S0 S4 S0 S0 S0 S12 S12 S12 
7  S0 S4 S0 S4 S0 –  –  – 
 
5. Press ENT for each entry. If you make a mistake, press CLEAR and enter the correct size code. 
 
Notes: 

  The default setting of the bank is for Motorola Type II. However, if you set Type I and you want to 

return to Type II, enter 15 at Step 4. 

  To confirm the input, repeat Steps 1-5 and press ENT. Each time you press ENT, you confirm the 

size code. If you find an error, press CLEAR and begin again at Step 1. 
 
6. Press SCAN to start scanning. 
 
talk group IDs 
 

Summary of Contents for Pro 2055



















































Reviews: