RadioLink R8FG Instruction Manual Download

Page: 5 / 11

RadioLink Electronic Ltd

www.radiolink.com

In order to enjoy this function, please upgrade

RC6GS(3-position switch version)

with the firmware

RC6GS_RadioLink_bin_1d15_V_6_1_2

downloaded via

https://www.radiolink.com/rc6gs_firmware

Or upgrade RC4GS(produced after 2018-01-01) with the firmware

RC4GS_RX_RadioLink_bin_2f50_V_6_0_1

downloaded via

https://www.radiolink.com/rc4gs_firmware

If you are using RC8X, RC6GS V3, RC6GS V2, RC4GS V3 or RC4GS V2, the default firmware supports
telemetry function.

Power on RC8X and R8FG receiver. The signal and other telemetry information will be displayed in the
home page of RC8X if the binding is successful and the telemetry cable is connected correctly.
RC8X home page:

2.1 Telemetry of Signal and RSSI

Power on RC8X and R8FG receiver, and then bind them. Signal and RSSI will be displayed on the
homepage of transmitter after successful binding.

Summary of Contents for R8FG












Search results

Summary of Contents for R8FG

Reviews:

Related manuals for R8FG

Brands by name

Popular brands

RadioLink R8FG, Instruction Manual

Search results

Summary of Contents for R8FG

Reviews:

Related manuals for R8FG

Brands by name

Popular brands