D2412 Installation Manual
Page 2
8/11/97 P/N 35115B
© 1997 Radionics
Notice
The material and instructions covered in this manual have been
carefully checked for accuracy and are presumed to be reliable.
However, Radionics, Inc. assumes no responsibility for inaccura-
cies and reserves the right to modify and revise this manual
without notice.
If a discrepancy is found in this documentation, please mail a
photocopy of the corrected material to:
Technical Communications
c/o Radionics, Inc.
1800 Abbott Street
P.O. Box 80012
Salinas, CA 93912-0012
© 1997 Radionics, Inc. Salinas, CA, U.S.A. All rights reserved.
FCC Notice
Part 15
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Part 68
This equipment complies with Part 68 of FCC rules. A label
contains, among other information, the FCC registration number
and ringer equivalence number (REN).
Radionics registered the D2412 Control/Communicator for
connection to the public telephone network using an RJ31X jack.
Use the ringer equivalence number (REN) to determine the
number of devices you can connect to the telephone line.
Excessive RENs on the telephone line may result in devices not
ringing in response to an incoming call. In most, but not all areas,
the sum of the RENs should not exceed five (5). Contact the
telephone company to determine the maximum REN for the
calling area.
If the D2412 Control/Communicator causes harm to the telephone
network, the telephone company will notify you in advance. If
advance notice isn’t practical, the telephone company will notify
the customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect the
operation of the D2412. If this happens, the telephone company
will provide advance notice in order for you to make the necessary
modifications to maintain uninterrupted service.
If you experience trouble with the D2412 Control/Communicator,
please contact Radionics Customer Service for repair and/or
warranty information. If the trouble is causing harm to the
telephone network, the telephone company may request that you
remove the D2412 from the network until the problem is resolved.
User repairs must not be made. Doing so voids the user’s
warranty.
Do not install the D2412 on public coin service provided by the
telephone company. Connection to Party Line service is subject to
state tariffs (contact your state public utilities commission for
information). You must supply the local telephone company with
the following information at their request:
• The line you are going to connect the panel to.
• Make (Radionics), model (D2412), and serial number of the
panel.
• FCC registration number and ringer equivalence for the
panel.
FCC Registration Number: ESVUSA-30727-AL-E
Ringer Equivalence: 0.3B
Service Center in USA: Radionics, Inc.
1800 Abbot Street
P.O. Box 80012
Salinas, CA 93912-0012
(800) 538-5807
Notice
The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommu-
nications network protective, operational, and safety require-
ments. Industry Canada does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local telecom-
munications company. The equipment must also be installed using
an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together.
Caution: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
www.PDF-Zoo.com
firealarmresources.com
