4
5
6
E
E
* For guidance only, depends on initial battery charge.
Your headset is a technically advanced device containing circuit boards and fine mechanics,
made from top grade component. To increase reliability and life span, always treat your headset
with care.
Do not expose the headset to moisture, liquids, rain or dust.
Store the product in a dry and dust-free location.
For cleaning, use a dry cloth.
Do not store a fully charged headset in the charging stand for extended periods of time.
Replacement ear cushions are available as spare parts.
E
2. Headset LED Display
Basic Operation
Switch on/off the Headset
1. To switch on the Headset, press and hold the "
Talk
" button until the Headset LED light on.
2. To switch off the Headset, press and hold the "
Talk
" button until the Headset LED turn off.
Charging Headset
1. Slide headset into charging cradle on the Base Station.
2. Gently press down on the headset to ensure that headset is in correct position. The battery
indicatory LED on base will turn on while charging.
Headset Registration
1. Press and hold the “
Register
” button on the Base station for 5 seconds until the in use LED
flashes.
2. Press and hold the “
Mute
” button on the Headset unit for 3 second until blue and red colour
LED flash.
3. After registration, LED on the base station and Headset will be off.
Adaptation to different host telephone
Slide the host phone cable selection switch from “
A
” to “
G
” until both the headset listening and
speaking volume have good sound quality. Position “
A
” is standard.
Answer Call
Ringing tone will be heard on headset receiver during incoming call. There is no ringtone on the
headset if you have not installed a lifter or EHS to your base station.
The handset lifter is
not
connected:
1. Take the handset off-hook.
2. Press the “
Talk
” button on the headset to answer a call.
The handset lifter is connected:
1. Press the “
Talk
” button on the headset to answer incoming call. in use LED on Base Station
will flash.
2. Press the “
Talk
” button again or place the headset into the charger to disconnect the call.
Make Call
The handset lifter is
not
connected:
1. Take your handset off-hook. Dial tone should sound through the handset.
2. Press the “
Talk
” button on the headset. The in use LED on both the base and the headset
should go on, indicating a successful link. Dial tone should sound through headset.
3. Dial using the telephone keypad.
4. Press the “
Talk
” button again or place the headset into the charger to disconnect the call.
The handset lifter is connected:
1. Press the “
Talk
” button on the Headset to connect to the Base Station. In use LED on Base
Station will flash.
2. Dial using the telephone keypad.
3. Base Station LED Display
Technical Specifications
Troubleshooting Guide
3. Press the “
Talk
” button again or place the headset into the charger to disconnect the call.
Note:Headset automatically enters off hook status when off cradle,just need entering the number to
dial out.
Adjusting microphone volume
Press the “
Microphone /-
” button to increase / decrease the speaking volume.
NOTE: You must be in talk mode (i.e. on a call) to adjust.
Adjusting base listening volume
Press the “
Listening /-
” button to increase / decrease the listening volume.
NOTE: You must be in talk mode (i.e. on a call) to adjust.
Muting the headset microphone
1. Press the “
Mute
” button on the headset, the microphone will be switched off. In use LED on base
will fast flash and beep tone will be heard on headset every 5 seconds while muted.
2. Press again the “
Mute
” button, the microphone will be switched on.
NOTE: You must be in talk mode (i.e. on a call) to adjust.
Adjusting headset listening volume
Rock the volume control or – (on the top of the headset) to adjust the listening volume.
NOTE: You must be in talk mode (i.e. on a call) to adjust.
Used equipment and used headset batteries must be disposed of in compliance with current
environmental protection regulations. You should return them to your reseller or dispose of
them at an approved recycling centre.
Do not attempt to open the batteries, as they contain chemical substance. In
the event of leakage, avoid contact with the skin, eyes and mouth. In the event
of contact, rinse the affected part for several minutes in running water. Clean
the product with absorbent paper or a dry cloth and contact your reseller for
replacement batteries.
We will repair or replace, at our discretion, this product if found defective due to materials or
workmanship within the warranty period beginning from the original date of purchase. This
product is warranted by authorized representative for the period specified. The Original dated
purchase receipt must be presented to the authorized service centre when service is rendered.
On all carry-in models, transportation to and from the service station is the responsibility of the
purchaser. This warranty does not cover damages due to accident, fire, flood, earthquake
and/or other acts of God; misuse, incorrect line voltage, improper installation, improper or
unauthorized repairs, commercial use or damages occurred in shipping. Exterior and interior
finish, lamps, glass, plastics parts and temperature probes are not covered under this warranty.
Customer adjustment according to the owner’s manual are not covered under this warranty.
This warranty is automatically void if the serial number is missing or altered.
Environment
Maintenance
Headset Operating Time:
(average values*)
AC / DC Adapter (For Base)
Telephone connection
Rechargeable Battery
Approx. 7 hours talk time
Approx. 120 hours standby time
For EU
INPUT: 100-240V
OUTPUT: 7.5Vdc 800mA
Single-phase AC excluding IT installations defined by the
EN60950 standard.
Caution: the network voltage is classified as a hazard by the
criteria of this standard.
Appliance designed for connection to an analogue telephone
line class TNV3 (telecommunications network voltage) as
defined by the EN60950 standard.
3.7Vdc / 320mAh
Event
Headset On cradle
Registration
In-use
Muting (In-use)
IN-USE LED indicator
Steady On
Moderate Flashing
Normal Flashing
Fast flashing
LED Indicators
Event
e
u
l
B
d
e
R
Slow Flashing
Steady On
Steady On
Alternate Red/Blue
Alternate Red/Blue
Normal Flashing
Normal Flashing
Fast Flashing
Standby
Charging
Charged
Registration
In-use
Out of Range
Ringing Signal
g
n
i
h
s
a
lf
w
o
l
S
y
r
e
V
y
r
e
tt
a
B
w
o
L
WARRANTY CARD
Note: THIS WARRANTY CARD WILL BE VOID IF IT IS NOT MAILED BACK TO OUR
COMPANY WITHIN 10 DAYS FROM DATE OF PURCHASE,WARRANTY
CONDITIONS (PLEASE SEE OVERLEAF)
Mr./Mrs./Miss/Co.
Telephone No.
Address
Model No.
Brand
Serial No.
Invoice No.
Dealer
Date of Purchase
S
N
O
I
T
U
L
O
S
S
M
E
L
B
O
R
P
The callers cannot
hear me.
Headset is muted. Press the "Mute" button on headset to unmute
the microphone.
Microphone volume is too low. Increase the microphone volume
by the "Micr" buttons on the base unit.
Sound in headset is
distorted/hear echo
in headset.
Reduce Microphone volume .
Listening volume too high on phone. If your phone has a handset
volume control, lower this until the distortion disappears.
If the distortion is still present, lower the listening volume adjust
button on the headset.
Base is too close to computer or phone.
I can hear too much
background
conversation, noise.
Speaking volume is too high. Lower the speaking volume.
Battery talk time
performance is
significantly
degraded even after
a full recharge.
Battery is going bad. Replace the battery with a new battery
pack.
S
N
O
I
T
U
L
O
S
S
M
E
L
B
O
R
P
The base station
does not work.
Check that the AC charger jack is connected to the base unit.
Check that the AC charger is securely connected to a working
outlet.
Check that the AC charger is the model supplied.
My headset does not
work.
Check that the phone is connected to the base unit’s phone cord
jack and it is pushed in firmly.
Check that the phone handset is connected to the base’s phone
handset jack and it is pushed in firmly.
Headset may be out of range of the base. Move closer to base
unit unti the headset is within range. Range varies with office
environment.
Headset battery is dead. Recharge the battery by placing the
headset in the Base Station.
Listening volume too low. Rock the volume up button on the
headset.
You may have to re-register your headset with the base.
Remark: A battery indicatory LED will flash once when inserting
the power into the base station.
The warranty period is 24 months.
The headset battery charging stays bar on the base station. This indicates the battery power status for the headset, the
battery power status is only displayed while headset is off the cradle. When the headset is docked on the cradle in the
charging position the four battery status LEDs on the base station will flash from green to red until the headset battery
is fully charged. Once the battery is fully charged all four battery status LEDs will be turned on constantly indicating the
battery is now fully charged. (Remarks: In order to have the battery level indicator on base station showing correctly.
your headset must be within operational range with the base station).
All 4 LEDs ON = Headset battery at full capacity.
Only 3 LEDs ON = Headset battery is above half capacity.
Only 2 LEDs ON + Headset battery is about half capacity.
Only 1 LED ON = Headset battery is low capacity.
The green LED on the base station indicates headset is almost fully charged. As soon as you remove the headset from
the base station, it is normal for the green LED to change to orange.
4.
