12
www.raider.bg
Depicted elements from second page.
1. SDS-plus replacement drill chuck
2. Tool holder (SDS-plus)
3. Dust protection cap
4. Locking sleeve
5. Auxiliary handle
6. Operational mode selection switch
1. General guidelines for safe operation.
Read all instructions carefully. Failure of the nature following instructions can cause electric
shock, fire and / or severe injuries. Keep these instructions in a safe place.
1.1. Work area safety.
1.1.1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
1.1.2. Do not operate in an environment where the hammer drill with an increased risk of
an explosion in the vicinity of flammable liquids, gases or powders. During operation of the
hammer drill can be separated sparks that can ignite powders or fumes.
1.1.3. Keep children and bystanders at a safe distance while working with the hammer drill.
If your attention is diverted, you may lose control over the hammer drill.
1.2. Electrical safety.
1.2.1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
1.2.2. Avoid touching your body to earthed bodies, e.g. pipes, heaters, stoves and
refrigerators. When your body is grounded, risk of electric shock is greater. Protect your
striking drill from rain and moisture. Penetration of water into the hammer drill increases the
risk of electric shock.
1.2.3. Do not use a power cord for the purposes for which it is not provided, e.g. to bear the
hammer drill for cable or removing the plug from the outlet. Protect cords from heat, oil, and
contact with sharp edges or points of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
1.2.4. When you work with the angle grinder out, switch the machine only in installations
equipped with electric switch “Fi” RCD (Residual Current Device). RCD must be no more than
30 mA. When use of extension cord is necessary always remember to use appropriate one up
to 15 m, section 1.5 mm
2
. Extension cord should be unwound whole. Use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
1.2.5. If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
1.3. Personal safety.
1.3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do
not use the hammer drill, when you are tired or under the influence of drugs, alcohol or narcotic
drugs. A moment of distraction at work striking drill may have the effect of extremely serious
injuries.
1.3.2. Work with protective work clothing and always with safety glasses.
Wearing Suitable for drilling shock and the activities of personal protective equipment, such
as respiratory masks, healthy, tightly closed shoes grapple with a stable, protective helmet and
silencers (hearing protectors), reduces the risk of accident.
1.3.3. Avoid the danger of incorporating the hammer drill inadvertently. Before you turn the
plug into the power supply network, make sure the trigger switch is in position “off”. If, when
you carry the hammer drill, keep your finger on the trigger switch, or if you submit a voltage of
the hammer drill, where it is included, there is the risk of accident.
1.3.4. Before you turn on the hammer drill, make sure that you have removed all of her
7. On/Off switch
8. Dust guard
9. SDS+ 14x250 mm pointed chisel
10. SDS+ 14x250 mm flat chisel
11. 3 pcs. drills “SDS-plus” Ø 8, 10, 12 x 150mm
Summary of Contents for RD-HD37
