13
1.29. Where transfer must tilt the machine when crossing zones without grass and when transporting
the machine to and from the area, which will mow, the machine must be switched off and the cutting blade
must be stopped.
1.30. Never lift or transport your lawn mower if the motor working and grass cutting blade is rotating.
1.31. Do not tilt the machine when the motor unless it is not necessary due to the presence of very
high grass. In this case, lift the remote side of the machine by pressing the handle down and then only as
necessary. When you run the machine, hold it firmly with both hands.
1.32. When you turn the power mower for grass to watch your feet are at a safe distance from rotating
parts.
1.33. Do not use the machine when you’re barefoot or in sandals. Always use a strong, closed shoes
and long trousers.
1.34. Switch off the On/Off switch and remove the plug from the mains electricity always:
when moving away from the machine;
before removal of items, which blocked the machinery;
when checking, cleaning or working on machinery;
when the machine starts to vibrate abnormally;
after coming into contact with a foreign body immediately check the machine for damage before it
benefit to removing them;
1.35. The operator or user responsible for accidents, injuries to others or the environment and caused
material damage.
1.36. Electric grass mower is designed so that all moving parts and hull ensure safe conditions for use.
For damage caused by attempts to change the structure of the electric grass mower manufacturer is not
liable.
1.37. In order to ensure safety should only use genuine parts or parts recommended by the manufacturer.
1.38. Failure to comply with the instructions may lead to electric shock, fire and / or severe injuries.
2. Functional description and purpose.
Electric mower is a manual with power isolation second grade. It is driven by a collector single-phase
alternating current motor and is designed for cutting grass at home. Not use the power mower for grass
operations other than its intended purpose.
3. Assembly of the components of the electric grass mower and commissioning.
Some of the mower parts are dismantled in order to reduce the volume of container during transport.
3.1. Mounting the handle.
Place the bottom of the two tubes of the handle in the openings of the housing so that the small
transverse holes for locking screws at both ends of the tubes to coincide with the smaller side openings in
the housing. Insert locking screws into the holes and screw them. Plug the device for holding the extension
cord, the tube of the upper handle. Install the top of the handle to lower handle with self-locking screws
and nuts with handles. Attach the switch in the upper part of the handle by means of two screws. Screw
them on the inner side of the handle so that the openings therein are aligned with holes in the housing of
the On/Off switch. Attach the power cord to the handle with clamp to hold the cable to the handle.
3.2. Assemble the plastic grass basket by joining the two parts. To this end, insert the pins of the lower
half in the corresponding holes in the upper half. Press until you hear a click. After assembling the basket
lift up the cover and attach underneath the finished basket on both hooks at the lown mower body. Submit
cover to lie on the basket. Always make sure the basket for collecting grass clippings is well secured! If
you do not need to collect the grass, it can mow without the basket, but necessarily with cover!
3.3. Place the wheels of the front and rear axles, put washer so that you can put cotter pin into the hole
in the axle. After inserting the cotter pin in the holeр distorted both ends in opposite directions. This will
ensure the wheels.
Easy and fast adjustment of the desired cutting height.
3.4. Check if the bolt that holds the blade is tight. Head bolt for spanner 27 mm, and the bolt itself has
a diameter of 8 mm and a right hand thread with step 1,25 mm. The length of the thread is 30 mm The bolt
is screwed to the right and to the left has been unscrewed. To unscrew or tighten the bolt catch with glove
the cutting blade to block the rotating of the shaft. Do not insert a screwdriver or other metal object into the
vent hole to block the rotation of the shaft. This will break the cooling turbine.
3.5. Firmly attached the extension cable for the device, then plug the extension cord plug to plug (2).
Summary of Contents for RD-LM32
Page 38: ...38 www raider bg EXPLODED VIEW AND SPARE PARTS LIST ...
Page 52: ...52 www raider bg ...
Page 53: ...53 ...