19
the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
1.4.5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
1.4.6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
1.4.7. Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
1.4.8. This appliance may be used by children aged 16 and over, as well as by persons with
limited physical, sensory and mental abilities or without experience and knowledge, if they are
under supervision or have been instructed in the safe use of the appliance and understand the
consequences of use. his dangers. Do not allow children to play with the appliance. Cleaning and
maintenance should not be performed by unattended children. Only have qualified electricians carry
out repairs and / or maintenance work.
1.4.9. Hot metal and sparks are blown from the cutting sheet. These sparks, hot metal, as well as
the heated workpiece and the heated equipment of the appliance can cause the use of the appliance,
check the working environment and make sure that it is suitable for work.
1.4.10.Remove all combustible materials at a distance of 10 m around the plasma cutting machine.
If this is not possible, carefully cover the items with suitable coatings.
1.4.11.Do not cut where flying sparks may fall on combustible material. Protect yourself and others
from flying sparks and hot metal.
1.4.12. Be careful, as sparks and hot materials can easily penetrate small cracks and openings in
adjacent areas when cutting. Keep in mind that cutting on a ceiling, floor or other surface can cause
a fire to ignite from the opposite, invisible Connect the cable as conveniently as possible to a socket
located near the work area to avoid spreading the power cord throughout the room and getting it on
an unfamiliar base that could cause electric shock, sparks, or fire.
1.4.13. Do not use the plasma cutter to defrost frozen pipes.
1.4.14. Danger of electric shock:
WARNING! Electric shock from a welding electrode can cause death.
1.4.15. Do not cut with the plasma cutting machine in rain and snow. Wear dry, insulating gloves.
Do not hold the electrode with bare hands. Do not wear wet or damaged gloves. Protect yourself
from electric shock by isolating it from the part. Do not open the housing of the appliance. Before
starting welding work, always check with a bright light source (eg a lighter) that the welding mask is
working properly. The safety glass can be damaged by splashes during welding. Replace damaged
or scratched safety glass immediately. Replace damaged or heavily soiled or sprayed components
immediately. The appliance may only be used by persons over 16 years of age. Familiarize yourself
with the welding safety regulations. Also observe the safety instructions for your plasma cutting
machine. Always put on the welding mask during welding. Failure to use the mask can cause severe
damage to the retina. Never use the welding mask without a protective glass, otherwise the optical
module may be damaged. There is a risk of eye damage! Replace the protective glass periodically for
good transparency and fatigue-free operation.
Danger from welding fumes: Inhaling welding fumes can endanger your health. Do not keep your
head in smoke. Use the devices in open areas. Use aspiration to remove smoke.
1.4.16 Danger due to welding sparks: Welding sparks can cause an explosion or fire. Keep
flammable substances away during welding. Do not use plasma cutting near flammable substances.
Welding sparks can cause fires. Place a fire extinguisher nearby and provide an observer who can
use it immediately. Do not weld barrels or closed containers.
1.4.17 Danger from electric arc radiation: Electric arc radiation can damage the eyes and injure the
skin. Wear a hood and goggles. Wear hearing protection and a high-necked collar. Wear a welding
mask and working sized filters. Wear complete body protection.
1.4.18 Danger due to electromagnetic fields: The welding current generates electromagnetic
Summary of Contents for RD-PCM29
Page 5: ...5 BG H ...
Page 78: ...78 www raider bg Exploded drawing of Inverter Plasma Cutting Machine RD PCM29 CUT 50 ...
Page 89: ...89 ...
Page 95: ...95 ...
