9
1. General guidelines for safe operation.
Read all instructions carefully. Failure of the nature following instructions can cause electric shock,
fire and / or severe injuries. Keep these instructions in a safe place.
1.1. Work area safety.
1.1.1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
1.1.2. Do not operate in an environment where the demolition hammer with an increased risk of
an explosion in the vicinity of flammable liquids, gases or powders. During operation of the demolition
hammer can be separated sparks that can ignite powders or fumes.
1.1.3. Keep children and bystanders at a safe distance while working with the demolition hammer.
If your attention is diverted, you may lose control over the demolition hammer.
1.2. Electrical safety.
1.2.1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce
risk of electric shock.
1.2.2. Avoid touching your body to earthed bodies, e.g. pipes, heaters, stoves and refrigerators.
When your body is grounded, risk of electric shock is greater. Protect your demolition hammer from
rain and moisture. Penetration of water into the demolition hammer increases the risk of electric shock.
1.2.3. Do not use a power cord for the purposes for which it is not provided, e.g. to bear the
demolition hammer for cable or removing the plug from the outlet. Protect cords from heat, oil, and
contact with sharp edges or points of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
1.2.4. When you work with the angle grinder out, switch the machine only in installations equipped
with electric switch “Fi” RCD (Residual Current Device). RCD must be no more than 30 mA. When use
of extension cord is necessary always remember to use appropriate one up to 15 m, section 1.5 mm
2
.
Extension cord should be unwound whole. Use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
1.2.5. If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
1.3. Personal safety.
1.3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do not use
the demolition hammer, when you are tired or under the influence of drugs, alcohol or narcotic drugs.
A moment of distraction at work demolition hammer may have the effect of extremely serious injuries.
1.3.2. Work with protective work clothing and always with safety glasses.
Wearing Suitable personal protective equipment, such as respiratory masks, healthy, tightly closed
shoes grapple with a stable, protective helmet and silencers (hearing protectors), reduces the risk of
accident.
1.3.3. Avoid the danger of incorporating the demolition hammer inadvertently. Before you turn the
plug into the power supply network, make sure the trigger switch is in position “off”. If, when you
carry the demolition hammer, keep your finger on the trigger switch, or if you submit a voltage of the
demolition hammer, where it is included, there is the risk of accident.
1.3.4. Before you turn on the demolition hammer, make sure that you have removed all of her
utilities and wrenches. Utilities, forgotten rotating unit can cause injuries.
1.3.5. Avoid unnatural positions of the body. Work in a stable position of the body at any time and
keep the balance. So you can control the demolition hammer better and safer if unexpectedsituations
arise.
1.3.6. Work with appropriate clothing. Do not operate with loose clothing or ornaments. Keep your
hair, clothes and gloves at a safe distance from rotating units of the demolition hammer. Robes, attire,
long hair can be caught and carried away by chuck.
1.3.7. If possible use an external aspiration system, make sure it is switched on and functioning
properly. Use of the aspiration system reduces the risks due to the discharge dust at work.
1.4. Demolition hammer use and care.
1.4.1. Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
Summary of Contents for RDI-DH01
