Raider RDP-CSCL03, User Manual

9

Detail, and attach with appropriate appliances or braces is anchored more firmly and securely than if you hold it by hand.
1.5.6.  Regularly clean your vent cordless screwdriver.
1.5.7.  Use only recommended battery and charger.
1.5.8.  Keep the battery away from heat sources. Do not leave the battery for a long time in high temperature (in direct sunlight, in 

proximity of heaters and wherever the temperature exceeds 50°C).

1.5.9.  The battery charging time cannot be longer than 3.5 hours. Otherwise the battery may be damaged.
1.5.10.  Avoid charging the battery in temperatures lower than 0°C.
1.5.11.  Charger supplied with the screwdriver is designed for operation with this product only. Do not use it for other purposes.
1.5.12.  Do not put any metal objects into the charger.
1.5.13.  Do not change direction of spindle rotation when the tool is operating. Otherwise screwdriver may be damaged.
1.5.14.  To clean the screwdriver use soft, dry cloth. Never use detergents or alcohol.
1.5.15.  Disconnect charger from power supply before cleaning.
1.6.  Special conditions regarding safety of charger operation.
Before using the charger read all relevant information contained within this manual, see markings on the charger and the product it is 

designed for.

1.6.1.  To reduce the risk of potential personal injuries use the charger for nickel-cadmium (Li-ion) batteries only. Other type batteries may 

explode and cause personal injury or material damages.

1.6.2.  Do not expose the charger to moisture or water.
1.6.3.  Use of any connecting elements not supplied or not recommended by the manufacturer of the charger may cause fire, personal 

injury or electric shock.

1.6.4.  Make sure the power cord is not located in pathway. It is not exposed to treading or other danger (e.g. strong tension).
1.6.5.  Do not use extension cord unless it is absolutely necessary. Use of improper extension cord may cause fire or electric shock. 

If it is necessary to use extension cord, first make sure that, extension cord socket matches plug prongs of the original charger power cord.

1.6.6.  Extension cord is in good technical condition.
1.6.7.  Do not use the charger with damaged cord or plug. Damage should be repaired by a qualified person.
1.6.8.  Do not use the charger after it has been hit, dropped or otherwise damaged. Entrust the testing and potential repair to authorized 

RAIDER service workshop.

1.6.9.  Do not try to dismantle the charger. All repairs are to be made by an authorized RAIDER service workshop. Improper charger 

assembly may cause electric shock or fire.

1.6.10.  Disconnect the charger from a power supply before starting any maintenance or cleaning.
1.6.11.  Disconnect the charger from mains network when it is not in use.

2. Construction and use.

Screwdriver is a battery-powered tool. Drive consists of DC commutator motor with permanent magnets and planetary gear. Screwdriver 

is designed for screwing in and out screws and bolts in wood, metal and plastics. Cordless, battery-powered power tools are especially useful 
for works in interior furnishing, adaptation of premises etc.

Use the power tool according to the manufacturer’s instructions only.

3. Noise level and vibration parameters.

Sound pressure: LpA = 72.89 dB(A) K=3 dB(A)
Sound power: LwA = 83.89 dB(A) K=3 dB(A)
Vibration acceleration: ah = 1.25m/s2 < 2,5 m/s2, K=1.5 m/s2.

4. Preparation for operation.

Charging the battery.
Screwdriver is supplied with partially charged battery. Charge the battery full before use. Charging the battery should be carried out in 

temperature between 4°C to 40°C. New battery, or one that have not been used for a long time, will reach full efficiency after approximately 
5 charge/discharge cycles.

The mains voltage must match the voltage on the charger rating plate.
Always check technical condition of the charger, charging station and power cord before starting to charge.
When charging the battery, use only the charger and the charging station supplied with the screwdriver.
Do not expose the charger and charging station to rain or splashing.
The battery charger supplied is matched to the Li-ion battery installed in the machine. Do not
use another battery charger.
The Li-ion battery is protected against deep discharging. When the battery is empty, the