Raider RDP-JS25, User Manual

12

www.raider.bg

construction, carpentry and other work-
related self-amateur activity.

8. Technical data
Information on noise and vibration

emitted.

The values are measured according to EN 

60745. A level of noise generated is generally: 
the sound pressure level 83 dB (A); sound 
power 94 dB (A). Uncertainty K = 3 dB.

Work with a silencer!
Full value of the vibration (the vector 

sum of the three directions) is determined 
according to EN 60745: Cutting of trees: 
vibrations generated a

h

 = 9.32 m/s

2

, 

uncertainty K = 1,5 m/s

2

, cutting plate: 

vibration generated a

h

 = 11 m/s

2

, uncertainty 

K = 3 m/s

2

. That level of vibration generated 

is representative of the most common uses of 
power. However, if jig saw is used for other 
activities, working with other instruments or 
if not maintained as prescribed, the level of 
generated vibrations can be changed. This 
could significantly increase the total load of 
vibration in the working process.

9. Installation of the cutting sheet.
9.1. Choice of cutting sheet.
Use only cutting sheets of T-shaped tail.

Cutting sheet should not be longer than 
necessary to implement the cuts. When 
cutting on a small radius arcs use the narrow 
cutting sheets.

9.2. Placement and replacement of the 

cutting sheet. Before carrying out any 
activities jig saw unplug the plug from the 
supply network. When mounting the cutting 
sheet work with protective gloves. Threaten 
to hurt yourself in contact with the cutting 
edges of the sheet. Prior to cutting the tail 
of the clean sheet. Contaminated tail can not 
be caught for sure. Move the handles of slot 
cutting sheet 8 so that you have easy access 
to hexagon bolts. Insert the cutting sheet at 
point blank into the slot for grip with the 
teeth facing in the direction of cutting. When 
you insert a sheet of careful cutting its rear 
edge to fall in the grooves of the lead pulley 
6. Precise cuts are possible only if the leading 
roller 6 rests against, but not too tight in
the back of the cutting sheet. Tighten well
hexagon bolts with the help of keys (4), which 
is located at the rear of a nozzle vibroshlayfa
to include aspiration system.

Replacement blade for use in the attached 

hexagon key set. Unscrew counterclockwise 
and the two screws holding the knife. Insert 
the new knife, then make sure the cutting 
attach sheet is healthy. If cutting sheet is 
snatched hard at work can be removed and 
you hurt.

10. Dust-extraction system.
Dust released during the processing of

materials such as paints containing lead, 
some wood, minerals and metals can be 
hazardous to health. By skin contact or 
inhalation of such powders can cause allergic 
reactions and / or respiratory illnesses to 
working with power tools or nearby persons. 
Certain powders, for example released 
during the processing of beech and oak are 
considered to be carcinogenic, particularly 
in combination with chemical treatment of 
wood (chromate, preservatives, etc.). Where 
possible, use dust-extraction system. Provide 
good ventilation in the workplace. The use of 
respiratory mask with a filter of class P2.

10.1. Inclusion of an aspiration system.
Put a hose nozzle aspiration system (3). 

Connect the hose (3) with an aspiration 
or vacuum system (some models have an 
optional adapter for a vacuum cleaner). Use 
a vacuum must be appropriate for work with 
the material being processed. If at work pays 
particular harmful to health or carcinogenic 
dust powder, use a specialized vacuum 
cleaner.

11. Job. with power tools.
Before carrying out any activities unplug

the plug from the power supply network.

11.1. Adjusting the angle of cutting.
For making major cuts in the slope plate 

(5) can be tilted left or right to 45 °. Unscrew
the screws (10) and gently move the main
plate (5). To establish accurate gradients of
the main shear plate is fixed at angles 0 °, 22,5 
° and 45 ° left and right. Tilt the main plate
(5) to the desired angle. Random slopes can
be set using a protractor. Then again tighten
the screws (10).

12. Commissioning.
Beware of the voltage of supply network!

Supply voltage of the network must conform 
to the details shown on the plate of power. 
Appliances marked with 230 V, can be 
supplied with a voltage of 220 V.

13. Inclusion and exclusion.
To turn the power switch trigger press