15
adaptor as an extension when using short driver bits.
5.7. Left - right direction of rotation.
Choose direction of spindle rotation with the selector switch (2).
Right rotation - move the switch (2) to the extreme left position.
Left rotation - move the switch (2) to the extreme right position.
Do not change direction of spindle when the spindle is rotating.
5.8. Drilling.
When you need to vent large diameter, is recommended first to break a small opening, which will
then be drilling to the desired size. This will prevent overloading the drill. Drilling deep holes should
be done gradually, as periodically removed from the drill hole to remove chips or dust. If during drilling
to drill block up in holes, you should exclude drill. Use a change of direction of rotation to remove
the drill from the hole. Drill must be kept in alignment with the hole. Ideally, the drill should be placed
perpendicular to the surface of the material being processed. If the condition for perpendicularity is
not respected at work can lead to trapped or breakage in drill hole and injury to the user. Continued
drilling at low speed the engine from overheating threatens. Must make periodic breaks during work or
to allow the drill to work on no-load maximum speed for about 3 minutes. Do not obscure the openings
in the hull used for ventilation of the engine.
5.9. Make periodic breaks at work.
5.10. Keep and refer to the accessories carefully.
5.11 Do not throw the tool, do not overload, do not soak in water and other liquids do not use it for
mixing adhesives and concrete coatings.
6. Operation and maintenance.
Clean the body with dry cloth. Do not use any cleaning agents, as they may damage the casing.
6.1 Replacing carbon brushes.
Exports (shorter than 5 mm), up or broken engine carbon brushes should be replaced. Always
replace both brushes simultaneously. Work on replacement of carbon brushes entrusted only to
qualified person with original spare parts in service of business RAIDER.
6.2. All faults should be repaired by RAIDER service workshop.
6.3. The repair of your power is best carried out only by qualified specialists, which used only
original spare parts. This ensures their safety operation.
7. Environmental protection
The machine, accessories and packaging should be sorted for environmental-friendly recycling.
Do not dispose of power tools into household waste!
According the European Directive 2012/19/EC for Waste Electrical and Electronic Equipment
and its implementation into national right, power tools that are no longer usable must be collected
separately and disposed of in an environmentally correct manner.
Summary of Contents for Solo RDP-SCDI20S
