GR8670-TB3 Quick Setup Guide
Product Illustration and Parts List
Important Notice
Front View
Rear View
HDD access light
A
HDD enclosure key lock
B
HDD enclosure button
C
Power status light
D
System status light
E
Thunderbolt
™
port
F
Mini DisplayPort
G
Power socket
H
Fan
I
Fan speed switch
J
Power switch
L
Anti-theft lock
M
Mute switch
K
GR8670-TB3 body
x1
Quick Setup
Guide
x1
The following items should be inside the package upon opening:
Product Parts List
Thunderbolt
™
Cable
x1
Power Cord
x1
Screws and key
The Indication of HDD Status
Important Notice
This system can only transfer data to one computer through one interface at a time.
The capacity of RAID 5 is the size of capacity of the smallest hard disk multiplied by 7, while RAID
0 is multiplied by 8. The result will be treated as one single high-capacity drive. A hard disk must
therefore be installed in every bay before this system can be used. We also recommend using
brand new hard disks with identical specifications from the same brand. If a hard disk needs to be
changed, please be sure to buy a hard disk with the same specifications, capacity, and brand. If this
is not possible, then the capacity of the new hard disk should be at least 20 GB larger than the
existing hard disk.
After the hard disk is formatted, the actual total capacity of the GR8670-TB3 detected by the
computer operating system will vary from the sum of all hard disk capacities stated by the
manufacturer.
All existing data will be deleted when this product is set up for the first time. Please ensure that all data
on the hard disk has been backed up before installation to avoid data loss.
Before a new HDD is installed in the GR8670-TB3, please make sure that there are no bad tracks
or defects to avoid data loss.
If the GR8670-TB3 needs to be shut down or disconnected, please ensure the HDD is safely
removed through your operating system before turning off the power.
To prevent data loss, do not remove any of the hard disks while the system is running.
Once the system has been initialized, do not switch hard disks around during use. Doing so may
prevent the RAID from being recognized by the system.
Once RAID mode has been set up, the switching of hard drives will lead to the removal of data from
the hard disks. Please be sure to backup the data on the hard disk before making any switches.
Under RAID 5 mode, the system can only tolerate the failure of one hard disk. If the system shows
that two or more of your hard disks have failed, your stored data may already be damaged or lost.
In RAID 0 mode, If the system shows that one of your hard disks has failed, your stored data may
already be damaged or lost.
If the GR8670-TB3 needs to be shut down or disconnected, please ensure the HDD is safely
removed through your operating system before turning off the power.
While the In-chassis temperature reaches up to 55 degree-C (131 degree-F), in order to get rid of
the heat efficiently, your DR8-TB3 will turn fan parts to full speed automatically. And once the
In-chassis temperature drops down to 50 degree-C (122 degree-F), you could then set fan speed
at Fan Speed Switch manually to reduce its fan noise for a better green environment at both of a
lower fan noise and the power saving.
We strongly recommend backing up important data stored on the GR8670-TB3 to another storage
device or a remote site. RAIDON will not be held liable for the damage or loss of data you stored
on the GR8670-TB3.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Please follow the steps below to complete the GR8670-TB3 hardware setup process:
Hardware Installation
Troubleshooting Fan Errors
The GR8670-TB3 includes a fan failure warning function. When the fan of the GR8670-TB3 fails, the
built-in buzzer will sound. The red warning light on the front plate will also light up; If this happens, press
the mute switch at the back of the system to turn off the buzzer. Next, turn off power to the GR8670-TB3
as soon as possible to let the machine cool down. Check to make sure that the machine is placed in a
well-ventilated location with nothing obstructing the fan, also check to see if the GR8670-TB3's fan has
stopped turning. Once the above checks have been completed, turn the power back on to continue
using this system. If this doesn't solve the problem, please contact the product supplier or RAIDON for
further technical assistance.
5. Once the hard disk is installed, slide the enclosure into the system and close the handle.
6. Select the appropriate cable from the accessories pack depending on the interface. Connect the
GR8670-TB3 backplate connection port to the corresponding port on the computer.
7. Connect the AC Power cable to the GR8670-TB3. Plug the connector into the power socket then
start the system.
8. Your operating system will automatically detect available capacity once the device finishes booting.
Once the device has been detected, please follow instructions given by the operating system and
format the system. Once the hard disk has been formatted, the GR8670-TB3 system can be used.
9. If the computer is unable to detect the system, please install the drivers from official website
(www.raidon.com.tw)
Note: Please avoid using hard disk drives from different manufacturers or different models
from the same manufacturer as this may impact system performance.
1. When you open the package, please immediately check the product and included parts for any
damage or missing parts. If there is a problem with the product or included parts please contact
your supplier immediately.
2. Place the device on a flat, even surface. Make sure that the cooling fan is not blocked and there
is sufficient surrounding space for cooling. (Keep away from water or other environments that may
cause product damage).
3. Please insert the pin included with the parts pack into the keyhole to release the HDD enclosure
handle and remove the HDD enclosure.
4. Place the hard disk in the HDD enclosure and secure it in place with the included screws; this will
prevent damage to the hard disk from external vibration.
Note:
If you do not have 8 HDDs, please follow the above HDD number
sequence to load all your in hand HDDs.
Hard Disk
Location 0
Hard Disk
Location 1
Hard Disk
Location 2
Hard Disk
Location 3
Hard Disk
Location 4
Hard Disk
Location 5
Hard Disk
Location 6
Hard Disk
Location 7
Please check the product and accessories for any defect or missing parts. If you have any
questions, please contact your product supplier.
Please visit the official website - Download page (http://www.raidon.com.tw/RAIDON2016/
download.php) to download drivers and other related resources.
˙
˙
Status
Power status light System indicator
Light
HDD Status
Light
Buzzer
No HDD detected Blue light always on
N/A
Red light always on
N/A
HDD failed
Blue light always on
Red light
flashing
Red light always on
YES
Data access
Blue light always on
N/A
Blue light flashing
N/A
HDD idle
Blue light always on
N/A
Blue light always on
N/A
Rebuilding data -
Source HDD
Blue light always on
N/A
Blue light flashing
N/A
Rebuilding data -
Target HDD
Blue light always on
N/A
Purple light flashing
N/A
Fan failure
Blue light always on
Red light
flashing
Blue light always on
YES
Overheat
Blue light always on
Red light
flashing
Blue light always on
YES
Thank you for choosing this
RAIDON
product.
The information provided in this manual was checked before publication, but the actual product
specifications may have changed before shipping; Latest product specifications and updates can be
found at
www.RAIDON.com.tw
or through your sales representative. No separate notifications will
be provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product
information, instruction manuals, or firmware, please contact
supporting@raidon.com.tw
for
assistance.
All product-related content in this manual are copyrighted by
RAIDON TECHNOLOGY, INC.
V1.0 (Jun. 2018)
