background image

Documentation Center

 WARNING

Do not power the device if any antenna port has been left open. In case you do not desire to use one or
more antenna feature, make sure to terminate the port with a 50 Ohm load.

2. Power on the Gateway

It is recommended to use a CAT5 Cable to provide power to the Gateway. Attach one end to the PoE injector and
the other to the Ethernet Port on the bottom of the casing.

Figure 34: Powering the Gateway using PoE

Access the Gateway

In this section, several ways in accessing the gateway are provided to have different alternatives for you to choose
depending on the availability of the requirements needed.

 WARNING

Do not power the device if the LoRa Antenna port has been left open to avoid potential damage in the
RAK7249 WisGate Edge Max."

Wi-Fi AP Mode

By default, the Gateway will work in Wi-Fi AP Mode which means that you can find an SSID named like
"RAK7249_XXXX" on your PC's Wi-Fi Network List. "XXXX" is the last two bytes of the Gateway MAC address.
To access the Web Management Platform, input the IP Address: 

192.168.230.1

 in your Web browser.

📝

 NOTE

No password is required to connect via Wi-Fi

Using your preferred Web browser, input the aforementioned IP Address and you should see the same Log-in
Page shown in the following image. Login the credentials provided below:

Summary of Contents for WisGate Edge Max





















Reviews: