III User Manual Pedelec with centre motor
9
1 Quick start
›
1. Charge the battery completely before riding for
the first time.
Unlocking the battery
›
2. To remove the battery, grip the handle, insert
the key into the lock and turn it anticlockwise. The
battery is now unlocked.
›
3. Tilt the battery sideways and lift it with both
hands out of the holder.
Tilt to remove
›
4. Put the battery in the docking station of the
charger. The battery LEDs light up or flash during
charging. You must fully charge the battery before
using it for the first time.
›
5. Once all LEDs have gone out, take the battery
out of the docking station.
›
6. Reinsert the battery into the holder on the
Pedelec from the left-hand side. Move the battery
outwards at an angle of roughly 45° as you do so,
as you did when you took it out of the holder. Move
the battery into the upright position until the lock-
ing mechanism engages. If the key is still in the
lock, you will need to turn it clockwise and pull it
out to allow the battery to lock in place.
›
7. Make sure that the battery is securely posi-
tioned and that the key is no longer in the lock.
›
8.
If your Pedelec is equipped with a LCD control
panel:
Continue at 10.
›
If your Pedelec is equipped with an LED control
panel:
Push the "Power" button on the control panel on
the handlebar.
Wait for 2 seconds before turning
the pedals
. The drive system requires this time
when no force is applied to the pedals to adjust the
power sensor correctly.
›
9. The intermediate power-assist mode appears
on the display panel of the LED control panel.
Press the "Mode" buttons to select the level of as-
sistance: "gentle / LOW", "intermediate / MID" or
"powerful / HIGH“. Press this button once to change
the assist level by one level. You can increase or
reduce the assistance, depending on which "Mode"
button you press.
›
10.
If your Pedelec is equipped with a LCD control
panel:
Push the "On / Off" button on the control panel on
the handlebar.
Wait for 2 seconds before turning
the pedals
. The drive system requires this period
after switching on during which no force is applied
to the pedals to adjust the power sensor correctly.
Press the "Assist" button to select the power assist
mode. This works in both directions. The assis-
tance output increases or decreases depending on
which “Assist” button you press. If you are using
the most powerful setting then press the button
again, you return to a mode without assistance.
Always operate one of the brakes before putting one
of your feet on a pedal as the motor pulls your bike
away immediately. This starting assistance is very
convenient, especially when starting on hills. If you
start off in road traffic or on unsurfaced roads without
controlling your speed, you could come off your bike
and seriously injure yourself.
›
11. You can now ride off.
Summary of Contents for Fast Pedelec
