14
III User Manual Pedelec with centre motor
4.2.1 Function of LCD control panel
4.2.1.1 On / Off button
Press the "On / Off" button to switch on the control panel
and drive.
The assist level that was active at the time the control
panel was switched off is automatically reinstated. The
back-lit display is turned on briefly then goes out. All
recording of data (trip, actual journey length, average
speed, top speed, total journey length) starts as soon
as you switch the control panel on and stops when you
switch it off.
4.2.1.2 Selector button for display panel
You can display the information "Trip", "Average speed",
"Top speed" and "Total journey length" consecutively
by pressing the selector button for the display panel
("Mode").
The setting that was selected when you switched off is
also displayed first in this case.
4.2.1.3 Changing the assist level
Increase power assist
The following assist levels are displayed one by one when
you press the button that increases the assist level:
"NO
ASSIST / no assistance"
,
"ECO / low assist level"
,
"STAND-
ARD / medium assist level"
,
"HIGH / high assist level"
, fol-
lowed once again by
"NO ASSIST / no assistance"
. This
means that the amount of assistance increases each time
you press the button until you reach the highest level. If
you subsequently press the button, the assistance switch-
es off.
Reduce power assist
If you press the button that reduces the assist level, the
assistance reduces each time the button is pressed and
returns to the most powerful assist level when it reaches
the end of the loop.
In the
"NO ASSIST / no assistance"
mode, you ride the bike
normally without the assistance of the motor.
4.2.1.4 Resetting recorded data
If you press the selector button for the display panel for
longer than three seconds with the control panel switched
on, this resets the trip, average speed and top speed read-
ings to zero. You cannot delete the total journey length
using this method.
4.2.1.5 Switching the display on and off
The back-lit display and LCD control panel display can
also be switched on even if the drive is not enabled. To
do this, press the button that switches the lights on. The
drive remains in "
NO ASSIST / no assistance" mode
. Now
you cannot change the assist level.
If you press the light button when the control panel is
switched on, the back-lit display turns on.
If you press the light button when the light is on, the back-
lit display turns off. The power assist is still available and
you can change the assist level.
4.2.1.6 Deleting all data
Press the display ("Mode") selector button and the button
that deletes all data on the rear of the control panel at the
same time to delete all the data stored, including the total
journey length. The display then automatically switches
to settings mode for language, LCD contrast and wheel
circumference.
Summary of Contents for Fast Pedelec
