background image

piping. 

When using test pressure of 1/2 psig or less to test the gas supply system, simply isolate 

the cooktop from the gas supply system by closing the individual shut-off valve. 

ELECTRICAL CONNECTION (certain models)

120volt, 60 Hertz,

 properly grounded dedicated circuit protected by a 15-amp or 20-amp circuit

breaker or time-delay fuse. 

Note: Use of automatic, wireless, or wired external switches that shut off power to the appliance

are not recommended for this product.

EXTENSION CORD CAUTIONS

Because of potential safety hazards associated with certain conditions, we strongly recommend

against the use of an extension cord. However, if you still elect to use on extension cord, it is

absolutely necessary that it be a UL-listed, 3-wire grounding-type appliance extension cord and

that the current carrying  rotting  of the cord in  amperes  be equivalent to, or greater than, the

branch circuit rating.

GROUNDING – IMPORTANCE (please read carefully.)

FOR   PERSONAL  SAFETY,   THIS  APPLIANCE   MUST   BE   PROPERLY  GROUNDED

(Certain models)

The power cord of this appliance is equipped with a

three-prong   (grounding)   plug   which   mates   with   a

standard   three-prong   grounding   wall   receptacle   to

minimize the possibility of electric shock hazard from

this appliance.

Where   a   standard   two-prong   wall   receptacle   is

encountered,

it is the personal responsibility and  obligation  of the

customer to have it replaced with a properly grounded

three-prong wall receptacle.

11

Summary of Contents for GC2-48N





















Reviews: