– 6 –
INPUT 17-32, when selected
(red), resets the fader strips to
control channel inputs 17 through 32, and buses 2, 4, 6, and
8. When selected, the faders move to the positions reflecting
the current settings for the layer, unless previously flipped.
To reset a flipped Channel Fader Strip, press the FLIP
button. To reset all the currently flipped Channel Fader
Strips, press the INPUT 17-32 Fader Layer control button
and hold it for two seconds. This will set all faders to the
selected layer.
AUX/BUS, when selected
(orange), resets the fader strips to
control the aux sends, aux returns, and bus outputs, while
the faders move to the positions reflecting the current fader
settings for the layer.
CUSTOM/MIDI is a user-definable Fader Layer control,
where the functions are selectable.
See Chapter 11, MIDI for more information on the
DA7 MIDI
feature, and Chapter 6, Fader Layers and Channel Strips
in the Users' Guide for additional information.
MONITOR Section
MONITOR Section
The
DA7 provides controls for two monitor outputs and a
talkback circuit. There are source selection LED buttons for
the MONITOR A and MONITOR B outputs, and LEVEL
knobs for both of the monitor outputs and the talkback
circuit.
MONITOR A Controls
The MONITOR A selection LED buttons route the input
selected
(green) to the MONITOR A OUTPUT (CR) (Control
Room) connections on the Rear Panel of the mixer and to
the headphones. The selections are:
8
L/R routes the MASTER L/R output to the monitors.
8
2TR A routes the device that is connected to 2TR A IN
on the Rear Panel to the monitors.
8
2TR B routes the device that is connected to 2TR B IN
on the Rear Panel to the monitors.
8
AUX routes the AUX SEND outputs to the monitors.
Press the AUX LED button to monitor the selections,
beginning with AUX SEND 1/2, followed by AUX SEND
3/4, and AUX SEND 5/6. The MEMORY numeric
readout on the Display Bridge will momentarily display
the AUX SEND selections.
The MONO button, when on
(red), sums the selected input
and sends a monaural signal to the monitors. This will not
affect the 2TR B output stereo signal.
MONITOR B Controls
The MONITOR B selection LED buttons route the input
selected
(green) to the MONITOR B OUTPUT (STUDIO)
connections on the Rear Panel of the mixer. The selections
are:
8
MONITOR A routes the current MONITOR A selection
to the studio monitors.
8
AUX routes the AUX SEND outputs to the monitors.
Press the AUX LED button to monitor the selections
beginning with AUX SEND 1/2, followed by AUX SEND
3/4, and AUX SEND 5/6. The MEMORY numeric
readout on the Display Bridge will momentarily display
the AUX SEND selections.
TALKBACK
The TALKBACK ON button controls the talkback
microphone installed in the Top Panel of the
DA7. When on
(orange), the MIC is active and the MONITOR A speakers
will be dimmed. This can be either a “push-to-talk”
momentary interrupt type button, or a “push on/push off”
type button. This is selected in the [UTILITY] window.
Talkback routing is selected in the [SOLO MONITOR]
window. There is also a phone jack on the Rear Panel that
allows for remote Talk back operation.
For additional information on the talkback, see Chapter 16,
Utility and Solo monitor in the Users' Guide.
SETUP Section
SETUP Section
These are direct-action buttons that will display the selected
windows in the LCD screen of the Display Bridge.
12
MONITOR A
MONITOR B
2TR A
L/R
MONITOR A
L/R
2TR B
AUX
AUX
MONO
0
10
0
10
0
10
T. B.
LEVEL
MONITOR
B LEVEL
MONITOR
A LEVEL
MIC
TALK BACK
ON
MONITOR A
source selection
buttons
MONITOR B
source selection
buttons
Talkback ON LED
button
LEVEL
knobs
SOLO
MONITOR
UTILITY
MIDI
D-I/O
GROUP
AUTOMATION
SET UP
MIDI button
UTILITY
button
GROUP
button
D-I/O button
SOLO MONITOR
button
AUTOMATION
button
13
