background image

WARRANTY

ALL  WARRANTIES  OF  THE  PRODUCTS  DESCRIBED HEREIN,
EXPRESSED  OR  IMPLIED,  INCLUDING   THE   WARRANTY   OF
MERCHANTABILITY   AND  FITNESS  FOR   PARTICULAR   PUR-
POSES,   ARE   SPECIFICALLY  EXCLUDED,  EXCEPT   FOR  THE
FOLLOWING: 

Ramset  will  repair  or replace, at  its sole option, any

tool, part, or fastener  which,  within  90  days  after sale by Ramset,
is  found by  Ramset  to be  defective  in  material  or  workmanship,
normal wear and tear excluded. 

THIS IS THE SOLE WARRANTY OF

RAMSET  AND  THE  SOLE  REMEDY AVAILABLE TO THE BUYER
AND IN NO EVENT WILL ANY DIRECT OR INDIRECT INCIDENTAL
OR  CONSEQUENTIAL DAMAGES,  OR  ANY  OTHER DAMAGES,
BE AVAILABLE.

Copyright 2000 ITW Ramset/Red Head

THE COBRA TOOLCOMPLIES WITH OSHA REQUIREMENTS

AND WITH ANSI A10.3 SPECIFICATIONS

FOR TOOL REPAIR SERVICE CONTACT YOUR LOCAL

AUTHORIZED ITW RAMSET/RED HEAD DISTRIBUTOR OR CALL

THE ITW RAMSET/RED HEAD TOOL REPAIR DEPARTMENT AT

1-800-354-7432

Wood Dale, IL 60191

     (630) 350-0370

Buy With Confidence ....

Buy From Your Authorized Diistributor

© ILLINOIS TOOL WORKS 2000

PRINTED IN THE U.S.A.

REVISED 1/00

Summary of Contents for Cobra Tool

















Reviews: