background image

SERVICING / TROUBLESHOOTING

SERVICING / TROUBLESHOOTING

11

SYMPTOM 

POSSIBLE PROBLEMS   SERVICE

Preparing Tool for Operation—Battery/Charger Problems 

— Battery Cell does not    — Inoperative indicator    — Try Battery Cell in tool after 3 hours  

  appear to accept  

  lights on charger 

  on charge cycle. If tool LED is 

  charge. Green charger     

  green, charger lights are not 

  light does not come on     

  working properly. Replace charger, 

   

   

  or monitor charging time to ensure  

   

   

  Battery Cell has adequate time for  

   

   

  recharging. It’s normal for Battery  

  

  

 to feel warm after properly charging. 

   

— Battery Cell damaged    — Replace Battery Cell 

   

  or cycle life exhausted

   

— Damaged charger 

— Discontinue use immediately and  

  

  

 unplug from power source. Replace  

   

   

  charger and tag or dispose of  

   

   

  charger to prevent accidental  

  

  

 reuse or connection to power source.

— Flashing lights on   

— Damaged Battery Cell  — Replace Battery 

  charger base unit 

— Battery Completely  

— Allow battery to charge for  

   

  Drained 

  5 minutes

Normal Stage of Operation 

— Fan does not run 

— Battery in off position  — Fully insert Battery

 

—tool LED is off

 

— Battery Cell is  

— Charge Battery Cell according to  

   

  not charged 

  Operating Manual.  

   

— Battery terminals or  

— Clean Battery Cell terminals.  

   

  battery contacts are 

  Battery Cell contacts as required. 

   

  oily, dirty, or corroded   

— Fan does not run,  

— Battery Cell is  

— Charge Battery Cell 

  or runs slower than 

  discharged 

  normal—tool LED is red
— Fan does not run,  

— Possible electronics 

— Remove, reinsert the Battery 

  tool LED flashes  

  error 

    Contact Authorized Ramset  

  red/green 

   

  Distributor Sales Representative 

   

   

  for service.

Pre-Combustion/Combustion Stage of Operation 

— Work Contacting   

 —Work Contacting  

— Remove and inspect Work Contact 

  Element does not  

  Element is bent, or 

  Element. Repair or replace Work  

  depress fully—tool  

  build-up of debris in 

  Contact Element as required. 

  does not operate  

  nose restricts operation  

   

— Tool is out of fasteners  — Add fastener strip

— Tool will not cycle 

— Fuel Cell is empty 

— Replace Fuel Cell 

  —fan runs, LED 

  is green 
   

— Spark does not occur.  — Contact Authorized Ramset  

   

   

  Distributor Sales Representative  

   

   

  for service.  

Summary of Contents for TF1200















Reviews: