background image

ICI2 Page 2 

 
 
 
 

RAMSEY TRANSMITTER KITS 

• 

FM-10C, FM25B FM Stereo Transmitters 

• 

TXE433 or 916 Transmitter & Encoder Module

 

• 

TV6C Television Transmitter 

• 

RX433 or 916 Data Transmitter 

• 

TX916 Data Transmitter 

• 

RR1 Wired remote repeater 

• 

RRW1 Wireless remote repeater 

 
RAMSEY RECEIVER KITS 

• 

FR1 FM Broadcast Receiver 

• 

AR1 Aircraft Band Receiver 

• 

SR2 Short-wave Receiver 

 
RAMSEY HOBBY KITS

 

• 

TFM3 Tri Field Meter 

• 

ECG1 Heart Monitor 

• 

WEB1 Walking Electronic Bug 

• 

LLS1 Laser Light Show 

• 

BE66 Blinky Eyes 

• 

PH14,15,16 Peak hold Meters, great for VU meters 

• 

LC1 Inductance-Capacitance Meter 

 
RAMSEY AMATEUR RADIO KITS 

• 

HR Series HF All Mode Receivers 

• 

QRP Series HF CW Transmitters 

• 

CW7 CW Keyer 

• 

CPO3 Code Practice Oscillator 

• 

QRP Power Amplifiers 

 
RAMSEY MINI-KITS 
Many other kits are available for hobby, school, Scouts and just plain FUN. New 
kits are always under development. Write or call for our free Ramsey catalog.    

 

ICI2 IR CONTROL INTERFACE KIT MANUAL

 

Ramsey Electronics publication No. ICI2 Revision 1.3 

First printing: January 2004 MRW/DAR

 

 
COPYRIGHT  2002 by Ramsey Electronics, Inc. 590 Fishers Station Drive, Victor, New York 
14564. All rights reserved. No portion of this publication may be copied or duplicated without the 
written permission of Ramsey Electronics, Inc. Printed in the United States of America.

 

Summary of Contents for ICI2





















Reviews: