background image

OM 914272-1114-A

LIMITED WARRANTY

 

RAMSEY WINCH COMPANY

 

Post Office Box 581510

RAMSEY WINCH warrants each new RAMSEY WINCH to be free from defects in 
material and workmanship for a period of one (1) year from date of purchase.

The  obligation  under  this  warranty,  statutory  or  otherwise,  is  limited  to  the 
replacement or repair at the Manufacturer's factory, or at a point designated by the 
Manufacturer, of such part that shall appear to the Manufacturer, upon inspection of 
such part, to have been defective in material or workmanship. 

This  warranty  does  not  obligate  RAMSEY  WINCH  to  bear  the  cost  of  labor  or 
transportation  charges  in  connection  with  the  replacement  or  repair  of  defective 
parts,  nor  shall  it  apply  to  a  product  upon  which  repair  or  alterations  have  been 
made, unless authorized by Manufacturer, or for equipment misused, neglected or 
which has not been installed correctly.

RAMSEY WINCH shall in no event be liable for special or consequential damages.  
RAMSEY  WINCH  makes  no  warranty  in  respect  to  accessories  such  as  being 
subject to the warranties of their respective manufacturers.

RAMSEY  WINCH,  whose  policy  is  one  of  continuous  improvement,  reserves  the 
right to improve its products through changes in design or materials as it may deem 
desirable  without  being  obligated  to  incorporate such changes  in  products of  prior 
manufacture.

If field service at the request of the Buyer is rendered and the fault is found not to 
be  with  RAMSEY  WINCH's  product,  the  Buyer  shall  pay  the  time  and  expense  to 
the  field  representative.    Bills  for  service,  labor  or  other  expenses  that  have  been 
incurred by the Buyer without approval or authorization by RAMSEY WINCH will not 
be accepted.

See warranty card for details.

Summary of Contents for Powermaster 15,000

























Reviews: