background image

O

peratOr

s

 M

anual

RAMTEQ

®

  

14275  northwest  freeway     

    houston,  tX    77040     

   phone:  713.983.6000     

    faX:  713.983.6405

   

  

300-00002-01 11/05

p

age

 

 

DO NOT operate this machine in areas where open flames are not permitted. DO NOT store or 

    use combustible materials on or near this machine. Use this equipment only in well ventilated

    areas. Failure to follow this warning may cause carbon monoxide build up, fire or explosion, and 

    possible injury or death.

 

DO NOT operate this machine while under the influence of alcohol, drugs or while fatigued.

 

DO NOT direct discharge stream at yourself or others. Risk of injection or injury may occur.

    Never put your hand or fingers over the spray tip. Do not try to stop or deflect leaks with your   

    hand or body. Always face nozzle and wand to the ground when testing.

 

DO NOT operate this machine wITHOUT wearing protective Eye wear. Gloves, Hard Hat, Mask,  

    Ear Plugs & Steel Toe work Boots are also recommended, DO NOT wear loose clothing. Keep 

    your body and clothing clear of the engine and discharge stream when the machine is running.

 

DO NOT tie back or block trigger gun in OPEN position. Never leave the pressure washer

    unattended once you have started it. If you leave, shut down machine completely.

 

DO NOT overreach or stand on an unstable support while operating this machine. Maintain 

    good footing and balance.

 

 

DO NOT permit this machine to run while unattended or for extended periods of time with

    trigger gun closed. Damage to pump may occur.

 

DO NOT operate this machine in an unsafe manner or around unsupervised children. Keep all 

    other personnel clear while operating this machine. This product should only be operated by 

    trained personnel.

 

DO NOT alter original factory settings prior to operating this machine. Risk of injury to yourself or 

    other persons may occur.

 

DO NOT remove hoses, guns, nozzles or any components while this machine is still hot or while 

    it is running.

 

DO NOT attempt to service this machine before reading the service manual.

 

DO NOT use water with a temperature over 140 degrees Fahrenheit

 

DO NOT use any electrical outlet that is not properly grounded or does not comply with all 

    federal, state, and local laws and/or electrical codes

 

DO NOT put diesel fuel in to a gasoline tank or gasoline into a diesel tank. Observe correct

    markings on fuel tanks before filling.

 

DO NOT operate this machine without knowing how to stop and bleed water pressures. Know all 

    controls before using this machine.

 

DO NOT spray caustic, acids or abrasive fluids through this machine.

 

DO NOT permit water to freeze inside this machine. Pump and plumbing damage may occur.

 

Use only recommended RAMTEQ parts when servicing this machine.

 

 

RAMTEQ will not be held liable for any unauthorized modifications made to this 

    machine. Any such action will void the warranty.

safety Guidelines

reaD tHIs FIrst!

  

FAIluRE TO REAd And ObsERvE All 

WARnInG sTATEMEnTs cOuld REsulT In sEvERE bOdIly 
InjuRy OR dEATh, POssIblE InjuRy TO OThER PERsOns, 
dAMAGE TO MAchInE OR OThER PROPERTy.

WARNING

Summary of Contents for BVE 1000





















Reviews: