Remote-Control Commands
Satellite Navigation
377
User Manual 1178.6379.02 ─ 01
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:UMOTion:STEP
<Resolution>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:STEP
<Resolution>
Sets the logging step.
Parameters:
<Resolution>
R1S | R2S | R5S | R10S | R02S | R04S | R08S
*RST:
R1S
Example:
See
Example "Enabling data logging"
Manual operation:
See
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:UMOTion[:CSV]:SELect:ALL
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:UMOTion[:CSV]:SELect:NONE
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:SELect:NONE
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:SELect:ALL
Enables or disables all of the available SV IDs.
Example:
See
Example "Enabling data logging"
Usage:
Event
Manual operation:
See
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:ACCeleration:ECEF
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:AZIMuth
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:CBIas
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:CPHase
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:DSHift
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:ELEVation
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:IDELay
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:POSition:ECEF
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:PRANge
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:PRANge:BIAS
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:PRANge:BIAS:RATE
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:PRANge:RATE
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:RANGe
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:RANGe:RATE
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:SLEVel
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:TDELay
<State>
[:SOURce<hw>]:BB:GNSS:LOGGing:CATegory:SATellite:VELocity:ECEF
<State>
Enables the parameter for logging.
Parameters:
<State>
0 | 1 | OFF | ON
*RST:
1
Example:
See
Example "Enabling data logging"
Data Logging