background image

Manual-1

AC 23B

ACTIVE CROSSOVER

OPERATORS  MANUAL

QUICK START

Labels

 above

 the controls refer to the unit being operated in the 2- or 3-Way 

Stereo

 mode. Labels 

below 

the

controls refer to the unit being operated in the 4- or 5-Way 

Mono

 mode.

Set the STEREO/MONO switch appropriately. The fact that the AC 23B is a multiple function unit means the outputs

are switched around in Mono mode.

To operate the unit in Stereo 3-Way mode, be sure the rear panel switches are set for STEREO 3-WAY. Following the

labels 

above

 the controls and jacks in logical order, you will find Channel 1 Master Input LEVEL, LOW Output, MID

Output, and HIGH Output, with the same for Channel 2.  If you need a summed Mono Low Ouput, see ‘Monoing the Low
Outputs’ on page Manual-7.

To use the unit as a Mono 5-Way, first check that the CHANNEL 1 and 2 switches are set to 3-WAY, and the other

switch is set to MONO. Connect the INPUT source to CHANNEL 1 

only

. Following the labels 

below

 the jacks, look at

SUB OUT, then look over at LOW OUT, now go back to MID OUT, then over to HIGH-MID OUT and then proceed to
the HIGH OUT. An internal switch determines 4 or 5-Way mode. Our apologies to 4-Way users: We must ship the units in
the 5-Way mode since normal Stereo 3-Way operation demands it: a fact not the least bit obvious, but nevertheless, a fact
it remains. Pity. See page Manual-6 for Mono 4-Way configuration.

In agreement with IEC and AES/ANSI standards, AC 22B wiring convention is pin 2 Positive, pin 3 Negative (return),

pin 1 chassis ground. See the “Sound System Interconnection” RaneNote included with this manual for more information
on cabling and grounding requirements.

CAUTION: Never connect anything except an approved Rane Power supply to the thing that looks like a red

telephone jack on the rear of the AC 23B.

 This is an 18 VAC center tapped power input. Consult the Rane factory for a

replacement or substitution.

WEAR PARTS:

 This product contains no wear parts.

MONO 4W OR 5W: INACTIVE

MID

MONO MASTER

SUBWOOFER

SUB / LOW

HIGH

LOW

LOW / MID

4W: MID / HIGH

5W: MID / HIGH-MID

4W: INACTIVE

5W: HIGH-MID / HIGH

4W: INACTIVE

5W: HIGH-MID

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

10

0

2

4

8

6

MAX

MIN

2

4

8

6

MAX

MIN

2

4

8

6

MAX

MIN

2

4

8

6

MAX

MIN

2

4

8

6

100

80

1k

900

850

150

200

240

750

600

400

190

250

7.0k

5.8k

550
475
350

700

2.0k
2.8k
4.5k

1.0k

190

250

7k

5.8k

550
475
350

700

2.0k
2.8k
4.5k

1.0k

100

80

1k

900

850

150

200

240

750

600

400

3W: MID / HIGH

2W: LOW / HIGH

3W: LOW / MID

2W: INACTIVE

2W: INACTIVE

3W: MID / HIGH

2W: LOW / HIGH

3W: LOW / MID

2W: INACTIVE

2W: INACTIVE

2W: LOW

ACTIVE

CROSSOVER

70

70

2W: LOW

LEVEL

LEVEL

MUTE

LEVEL

LEVEL

MUTE

FREQUENCY

DELAY

DELAY

LEVEL

FREQUENCY

FREQUENCY

LEVEL

DELAY

MUTE

FREQUENCY

LEVEL

DELAY

MUTE

LEVEL

AC 23B

CH 2

MASTER

CH 1

MASTER

POWER

FREQUENCY

LOW

MID

LOW

MID

HIGH

HIGH

Summary of Contents for AC 23B

















Reviews:

Related manuals for AC 23B