Rangemaster Professional 90 Gas FSD, User Manual

33

WARNING  -  SERVICING  TO  BE  CARRIED  OUT  ONLY  BY  AN  AUTHORISED  PERSON 

Disconnect  from  electricity  and  gas  before  servicing.  Check  appliance  is  safe  when  you  have  finished. 

of electrode and fit to new electrode. Fit new electrode 

to burner.
Reassemble in reverse order. Check ignition.

20. To Remove Grill Door

Remove L H side panel (see 3). Remove the plinth 

(4 screws) and the central vertical cover (5 screws). 

Remove the two countersunk screws (1 each side) 

securing the grill hinge arms to the front of the grill 

chamber.

NOTE:

 The arms are spring tensioned. Carefully 

remove the grill door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket 

is fitted between the hinge arm and the front of the grill 

chamber.

21. To Remove Main Oven Door

Open oven door and remove Handyrack (where fitted) 

by springing one side out of the bracket on the door and 

sliding the other side free. Support the door and remove 

the two screws securing the upper hinge and packing to 

the cooker front. Remove the door from the lower hinge 

by lifting slightly and moving outwards.
Reassemble in reverse order.

22. To Change Main Oven Door Outer Panel

Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel 

fixing screws from the door sides (two each side). 

Carefully lift off the outer door panel. 
Remove door handle from panel by unscrewing 2 

retaining nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.

23. To Change Main Oven Door Latch

Remove outer door panel (see 15). Remove screws 

‘B’ holding latch assembly to inner door panel. Fit new 

catch and reassemble in reverse order.
Check correct door operation.

24. To Change Oven Door Seal

Open oven door. The seal is held in place by small 

hooks on the rear face. At the corner pull seal diagonally 

away from the door centre until that hook is released. 

Proceed to the next hook and release it in a similar way, 

and so on. Use force if the hooks are stiff, as the old 

seal will be discarded.

When fitting new seal, position the seal join at the 

bottom. Hook the new seal in one of the corner holes of 

the door, and proceed round the door snapping in each 

hook in turn.

25. To Adjust Main Oven Door Catch Keep

Open oven door, slacken off locknut at base of keep, 

and screw in or out as required until required fit is 

obtained. Retighten locking nut.

26. To Remove Fan Oven Inner Back.

Open RH oven door and remove 4 screws and 

washers securing the inner back to the back of the 

oven. Carefully lift away the inner back. Reassemble 

in reverse order making sure that the 4 screws and 

washers are fully tightened.

27. To Remove Tall Oven Door

Open oven door, support the door and remove the two 

screws securing the upper hinge and packing to the 

cooker front. Remove the door from the lower hinge by 

lifting slightly and moving outwards.
Reassemble in reverse order.

28. To Change Tall Oven Door Outer Panel

Remove oven door see 16. Lay door face down on a 

suitable surface and remove 2 screws from bottom edge 

of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by 

unscrewing 2 screws. Remove 2 cross-headed screws 

holding door handle fixing bracket to door panel. Fit 

door handle bracket and door handle to new panel.
Fit panel to door. Reassemble in reverse order.

29. To Change Tall Oven Door Magnetic Latch

Remove the control panel (see 4).
Remove the plinth (3 screws) and the central vertical 

cover (5 screws). Prize the retaining clip off the magnet 

unit. Fit new unit and retaining clip.
Reassemble in reverse order.
Check correct door operation.

30. To Change Ignition Generator

Disconnect from electricity supply.