Rangemaster U109300 - 01, User Manual & Installation & Service Instructions

35

WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

18. To Change Tall Oven Door Outer Panel

Remove oven door see 16. Lay door face down on a 
suitable surface and remove 2 screws from bottom edge 
of door and 2 screws from inside face of door.

Remove outer door panel. Remove door handle by 
unscrewing 2 screws. Remove 2 cross-headed screws 
holding door handle fi xing bracket to door panel. Fit door 
handle bracket and door handle to new panel.

Fit panel to door. Reassemble in reverse order.

19. To Change Tall Oven Door Magnetic Latch

Remove the control panel (see 4).

Remove the plinth (3 screws) and the central vertical cover 
(5 screws). Prize the retaining clip off  the magnet unit. Fit 
new unit and retaining clip.

Reassemble in reverse order.

Check correct door operation.

20. To Remove Grill Element.

Disconnect from electricity supply.

Remove grill pan from grill chamber. From inside grill 
compartment remove enamelled front shield from grill 
roof, 2 screws and washers. Remove 2 screws and washers 
securing the grill element front support. Remove the 
screws from the grill elements.

Lift elements out carefully, disconnect the leads from the 
element terminals noting their position. If it is not possible 
to disconnect the leads in this way, pull cooker forward 
to gain access to the rear, remove screws securing the 
electric cover to the back sheet and remove cover and 
disconnect the terminals from the rear.

Fit new elements, reassemble in reverse order. Check 
operation of grill.

21.  To Remove Oven Inner Back.

Open the oven door and remove the screws and washers 
securing the inner back to the back of the oven.

Carefully lift away the inner back. Reassemble in reverse 
order making sure that the 4 screws and washers are fully 
tightened. 

22. To Change Fan in Oven.

Disconnect from electricity supply.

Pull cooker forward to gain access to the rear. Remove 
screws securing the electric cover to the back sheet and 
remove cover. Disconnect the 3 terminals connected to 
the fan noting their position. Remove oven inner back 
(see 20). Hold the fan blade and remove the centre nut 
(left hand thread) 2 brass washers, fan blade and Circlip. 
Unscrew fan retaining nuts and washers (3 off  each) and 
lift the fan away from the rear of the cooker. Fit new fan 
and reassemble in reverse order. Check operation of oven.

23  To Remove an Oven element Thermal Cut-Out.

Disconnect from the electricity supply.

Pull the cooker for ward to gain access to the cover box. 
Undo the cover screws and lift clear. The cutout is located 
on the earth plate be side the oven element con nec tions. 
Disconnect the cutout wir ing. Undo the fi xings that secure 
the cutout to the earth plate and re move. Fit re place ment 
control and re-as sem ble in reverse order.

24.  To Remove Oven Element.

Disconnect from electricity supply.

Remove oven inner back (see 22).

Remove 2 screws from the top of the element and 1 from 
the bottom of the element in side the oven. Lift element 
out carefully, disconnect the terminals connected to 
the element noting their positions. If it is not possible 
to disconnect the leads in this way, pull cooker forward 
to gain access to the rear, remove screws securing the 
electric cover to the back sheet and remove cover and 
disconnect the terminals from the rear.

Fit new element, and reassemble in reverse order. Check 
operation of oven.

25.  To Remove the Left Hand Oven Bottom & Top 

Elements

Disconnect from the electricity supply.

Bottom Element

Pull the cooker forward to access the cover boxes at the 
rear of the unit. Remove the fi xings that secure the cover 
and lift it clear.

Remove the 2 screws ‘A’ and allow the plate to drop down. 
Remove the 2 screws B, lower the upper plate and remove 
through the slot in the cooker back.

Undo the terminal connections, noting their positions.