DK
5
Sikkerhedsforskrifter
1. Før montering eller vedligeholdelse skal du altid slukke for strømforsyningen for
at undgå elektrisk stød.
2. Lampen skal have jordforbindelse.
3. Hvis lampens eksterne fleksible ledning er beskadiget, skal den med det
samme udskiftes af producenten, en servicetekniker, eller en faglært elektriker
for at undgå farlige situationer.
4. Før der udføres vedligeholdelsesarbejde, skal der slukkes for strømmen.
Vedligeholdelsesarbejdet må kun udføres af en autoriseret elektriker.
5. DT- DT-826642: Apparatet er udstyret med stik. Sørg for, at det
samlede output er max. 13A.DT-826420 er med schuko stik og det samlede
output er max. 16A.
6. Lampen må kun bruges, når beslaget er udstrakt.
Korrekt bortskaffelse af produktet
Dette mærke betyder, at produktet ikke må bortskaffes sammen med andet husholdningsaffald
i hele EU. For at undgå forurening af miljøet eller skader på menneskers helbred som
følge af ukontrolleret bortskaffelse af affald, bør produktet genbruges ansvarligt for at
fremme bæredygtig genbrug af materialeressourcer. Det brugte apparat kan returneres
via retur- og indsamlingssystemet eller ved at kontakte forhandleren, hvor produktet er
købt. De kan sikre, at produktet genbruges miljømæssigt forsvarligt.
A. Cover
B. LED
C. Hus
D. Håndtag
FORSIGTIG:
Lampens lyskilde kan ikke udskiftes.
Hvis den går i stykker, skal lampen
udskiftes.
E. Kontakt
F. Stik
G. Beslag
H. Driver
LED LIGHT INSTRUCTIONS
Read the User Instructions carefully before use.
Save these instructions for future reference.
Do not look directly into the work lamp when it is switched on.
Keep out of the reach of children.
Can be used indoors and outdoors. Charge the lamp in dry, indoor location.
Do not immerse in water or any other liquid.
Specifications
Type
Rated Power
Supply
Current
Power
factor
Tempered
Glass
Weigh
t
Maximum
projected
area
Dimensions
Remark:
Electric shock
protection class:
I
External light
protection class:
IP54
Lamp socket size:
LED
Rated
voltage:220-240V~
50/60Hz
DT-8264
13
45W
（
250*0.2W
）
MAX.0.2
1A
＞
0.9
347*194*2.3
mm
2.3kg
0.07M
2
385*315*90m
m
Safety instructions
1. Before mounting or maintenance, always switch off the electrical supply to avoid electric shock.
2. The lamp must be earthed.
3.The power cord must be H07RN-F 3x 1.5 mm² cable waterproof.
4.If the external flexible cable or cord of this luminaire is damaged, it must immediately be replaced by the
manufacturer, his service agent or a qualified technician.
5. Replace any cracked protective shield.
6.Before maintenance work takes place, the power must be switched off. The maintenance should be done
only by a qualified electrician.
7.
The appliance is equipped with sockets. Make sure that the total output is less than 16A.
8.The lamp must only be used with the bracket extended.
A. Cover
B. LED
C. Body
D. Handle
E. Switch
F. Socket
G. Bracket
H. Driver
LED LIGHT INSTRUCTIONS
Read the User Instructions carefully before use.
Save these instructions for future reference.
Do not look directly into the work lamp when it is switched on.
Keep out of the reach of children.
Can be used indoors and outdoors. Charge the lamp in dry, indoor location.
Do not immerse in water or any other liquid.
Specifications
Type
Rated Power
Supply
Current
Power
factor
Tempered
Glass
Weigh
t
Maximum
projected
area
Dimensions
Remark:
Electric shock
protection class:
I
External light
protection class:
IP54
Lamp socket size:
LED
Rated
voltage:220-240V~
50/60Hz
DT-8264
13
45W
（
250*0.2W
）
MAX.0.2
1A
＞
0.9
347*194*2.3
mm
2.3kg
0.07M
2
385*315*90m
m
Safety instructions
1. Before mounting or maintenance, always switch off the electrical supply to avoid electric shock.
2. The lamp must be earthed.
3.The power cord must be H07RN-F 3x 1.5 mm² cable waterproof.
4.If the external flexible cable or cord of this luminaire is damaged, it must immediately be replaced by the
manufacturer, his service agent or a qualified technician.
5. Replace any cracked protective shield.
6.Before maintenance work takes place, the power must be switched off. The maintenance should be done
only by a qualified electrician.
7.
The appliance is equipped with sockets. Make sure that the total output is less than 16A.
8.The lamp must only be used with the bracket extended.
A. Cover
B. LED
C. Body
D. Handle
E. Switch
F. Socket
G. Bracket
H. Driver
Summary of Contents for DT-826413
Page 15: ......
