Index
665
Server Reachability Configuration Commands
• 476
Server Reachability Information • 373
Server Reachability Information for a Specific
Server • 374
Setting an LED Color for a Rack Unit • 487,
488
Setting an LED Mode for a Rack Unit • 487,
488
Setting an Outlet's Cycling Power-Off Period •
437
Setting an Outlet's Thresholds • 215, 216
Setting an Overcurrent Protector's Thresholds
• 218, 219
Setting Asset Sensor LED Colors • 80, 297
Setting Data Logging • 147, 385
Setting Data Logging Measurements Per Entry
• 385
Setting Default Measurement Units • 138, 159,
447, 450
Setting EAP Parameters • 392
Setting Front Panel RCM Self-Test • 586
Setting Inlet Thresholds • 218
Setting IPv4 Static Routes • 399
Setting IPv6 Static Routes • 403
Setting LAN Interface Parameters • 403
Setting LED Colors for Connected Tags • 485,
487, 488
Setting LED Colors for Disconnected Tags •
486, 487, 488
Setting Network Service Parameters • 404
Setting Non-Critical Outlets and Load
Shedding Mode • 206, 238, 384
Setting NTP Parameters • 412, 498
Setting Power Thresholds • 107, 192, 210,
215, 339
Setting RCM Current Thresholds • xxi, 572,
575, 576, 585
Setting RCM Thresholds • 584
Setting the Alarmed to Normal Delay for
DX-PIR • 461
Setting the Authentication Method • 391
Setting the Automatic Daylight Savings Time •
414
Setting the BSSID • 395
Setting the Cascading Mode • 28, 29, 82, 115,
142, 144
Setting the Date and Time • 134, 340
Setting the Default Outlet State • 199
Setting the EnergyWise Configuration • 153
Setting the History Buffer Length • 490
Setting the HTTP Port • 405
Setting the HTTPS Port • 406
Setting the Initialization Delay • 193, 203, 384
Setting the Inrush Guard Delay • 204
Setting the Inrush Guard Delay Time • 383
Setting the IPv4 Address • 396
Setting the IPv4 Configuration Mode • 396
Setting the IPv4 Gateway • 397
Setting the IPv4 Preferred Host Name • 396
Setting the IPv4 Primary DNS Server • 397
Setting the IPv4 Secondary DNS Server • 398
Setting the IPv4 Subnet Mask • 397
Setting the IPv6 Address • 401
Setting the IPv6 Configuration Mode • 400
Setting the IPv6 Gateway • 401
Setting the IPv6 Preferred Host Name • 400
Setting the IPv6 Primary DNS Server • 401
Setting the IPv6 Secondary DNS Server • 402
Setting the LCD Display's Default View • xix,
62, 138
Setting the LED Operation Mode • 487
Setting the Networking Mode • 389
Setting the Outlet Initialization Delay • 384
Setting the Outlet Power-On Sequence • 205,
381
Setting the Outlet Power-On Sequence Delay
• 381
Setting the Outlet Relay Behavior • 193, 380,
383, 384
Setting the Outlet-Specific Default State • 193,
200
Setting the Outlet-Specific Power-On Delay •
206
Setting the PDU-Defined Cycling Power-Off
Period • 383, 437
Setting the PDU-Defined Default Outlet State •
382, 436
Setting the PDU-Defined Default State • 193,
200, 201
Setting the Polling Interval • 481
Setting the PSK • 391
Setting the Serial Port Baud Rate • 490
Setting the SNMP Configuration • 408
Setting the SNMP Read Community • 409
Setting the SNMP Write Community • 409
Setting the SSID • 391
Setting the sysContact Value • 409
Setting the sysLocation Value • 409
Setting the sysName Value • 409
Setting the Time Zone • 340, 414
Setting the X Coordinate • 459
Setting the Y Coordinate • 459
Setting the Z Coordinate • 386, 460
Summary of Contents for PX3-4000 series
