Panta-V7 Wireless Profile Safety Precautions
• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not
attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it
’
s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6
”
(15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out` doors voids all warranties.
• During long periods of non-use, disconnect the unit
’
s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular attention to the point they exit from
the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer.
• Heat -The appliance should be situated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in
performance.
Panta-V7 Wireless Profile Set Up
P
ower Supply:
The Rasha Tint Wireless Profile contains switching (multi Voltage) voltage
switch, which will auto sense the voltage when it is plugged into the power source. With this
switch there is no need to worry about the correct power voltage; this unit can be plugged in
anywhere. Light can recharge and use at same time.
DMX-512:
DMX is short for Digital Multiplex. This is a universal protocol used as a form of
communication between intelligent fixtures and controllers. A wireless transmitter/ DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as
serial data that travels from fixture to fixture via the wireless DMX receiver/DATA
“
IN
”
and
DATA
“
OUT
”
XLR terminals located on all DMX fixtures (most controllers only have a DATA
“
OUT
”
terminal).
DMX Linking:
DMX is a language allowing all makes and models of different manufactures to
be linked together and operate from a single controller, as long as all fixtures and the controller
are DMX compliant. To ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible or connect wireless transmission. The order
in which fixtures are connected in a DMX line does not influence the DMX addressing. For
example; a fixture assigned a DMX address of Addr-A001 may be placed anywhere in a DMX
line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX
address of A001, the DMX controller knows to send DATA assigned to address A001 to that
unit, no matter where it is located in the DMX chain/Controller.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Panta-V7 Wireless
Profile can be controlled via DMX-512 protocol/Wireless DMX transmitter. The Panta-V7
Wireless Profile has 5/9 DMX channel modes,. The DMX address is set on the back panel of
the Panta Wireless Profile. Your unit and your DMX controller require a standard 3-pin XLR
connector/wireless DMX Transmitter for data input and data output. We recommend
Rasha-Cable DMX cables/Wireless Transmitter. If you are making your own cables, be sure to
use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro
lighting stores) or 2.4Mhz Wireless Transmitter/Receiver. Your cables should be made with a
male and female XLR connector on either end of the cable. Also, remember that DMX cable
must be daisy chained and cannot be split.
