background image

Operation Manual RAVAS Proline Touch Basic 

Rev. 6

 

Weighing Terminal 

This manual describes the basic functions and the operation of the Proline Touch weighing terminal with the 
operator interaction in the individual steps of the operating sequence. The terminal is intended for connection 
to 12 V DC power supply (

–15%) to 30VDC (+10%).  

The weighing terminal supports power saving functions for battery operation: 

 

 

On / off for printer; 

 

Power off for display backlighting after time; 

 

Power off for terminal when not in use after time; 

 

Power off on battery low after warning. 

 

2.1 

Documentation 

Apart from this documentation, additional information is provided in the following manuals: 

 

Technical Manual 

IT6000ET

 

Calibration Manual 

ADU. 

 

 

2.2 

Safety Advice 

 

 

Read this manual carefully before you operate this instrument! Keep this manual for future 
reference! 

 

It must be installed, serviced, and operated in strict compliance with all locally applicable safety 
regulations and the rules for the prevention of accidents! 

 

When this unit is included as a component part of a system, the resulting system design must be 
reviewed by qualified personnel who are familiar with the construction and operation of all 
individual components in the system and the potential hazards involved. Failure to observe this 
precaution could result in bodily injury! 

 

All switch gear connected to the unit and/or installed close to it, such as relay and  contactors, 
must be fitted with appropriate components (RC-modules, diodes) to suppress interference. 

 

This module and its associated equipment must be installed, adjusted and maintained by 
qualified personnel only! 

 

Only permit qualified personnel to operate this instrument! 
Disconnect all power to this instrument before cleaning and servicing! 

 

Exercise utmost care when making checks tests and adjustments that can actuate movable 
parts such as feeding devices, gates, flaps, conveyors, etc. Make absolutely sure that nobody is 
within reach of movable parts. Failure to observe this precaution could result in bodily injury! 

Summary of Contents for ProLine Touch Basic


















































Reviews: