Ravelli DUAL 9 SUPER Use And Maintenance Manual Download

Page: 61 / 174

Use and maintenance manual

Dual 9 super

Rev.1 26/03/2018

Pag.61

User’s manual HANDHELD TOUCH RADIO

Pag.24

Pag.25

Vers. 01 of:07.04.14

Settable switch-on program

Settable switch-off program

Day of the week with active program

Number of "chrono" program (1-2-3-4)

Setting the power upon programming

Setting ambient temperature

MENU

CHRONO

ENABLE CHRONO

SET CHRONO

SET CHRONO 1

SET CHRONO 2

SET CHRONO 3

SET CHRONO 4

ENABLE CHRONO

CHRONO

USER

MANUFACTURER

ENGINEER

MANUFACTURER

ENGINEER

USER

SCREW FEEDING

CHRONOTHERMOSTAT

AIR-PELLET SET

STOVE STATE

AIR-PELLET SET

STOVE STATE

MENU

Flow

MANUFACTURER

ENGINEER

USER

SCREW FEEDING

CHRONOTHERMOSTAT

AIR-PELLET SET

STOVE STATE

CHRONOTHERMOSTAT

AIR-PELLET SET

STOVE STATE

USING THIS METHOD, IT IS NECESSARY TO VERIFY THAT AFTER EACH AUTOMATIC SHUTDOWN

THE GRATE IS ALWAYS VERY CLEAN TO GUARANTEE CORRECT AUTOMATIC SWITCH ON.

AUTOMATIC SWITCH ON.

The first setting allows the activation of the CLIMATE COMFORT function. This function is intended to ensure that the room tem

-perature set is maintained steady upon setting the maximum period of “X” minutes (SWITCH-OFF DELA

Y: 5 MIN) before switch-ing to ECO STOP phase. The STOVE maintains this state until the temperature drops below the set

value (CLIMATE COMFORT DELTA : 5℃).

For example, with the room temperature at 21 ° C, the stove switches of f when this temperature is

reached and restarts when the temperature reaches 15°C (21°C - 5°C - 0,5°C tolerance).

You can also activate the function using an external thermostat, keeping in mind that this does not include the value of the hyster

-esis.

We recommend you use an external thermostat with a histeresys value that can be set to maximum 3°C.

The operation of the stove could activate the switch ON/OFF phases for several times during the day;

this may affect the service life of the ignition coil.

Description of menu functions

Press the key to access the MENU page

The TECHNICIAN and MANUFACTURER menus are protected by password.

Chronothermostat

With the Chrono-thermostat function you can program the automatic switch ON/OFF of the stove for each day of the week

for each day of the week in 4 independent time intervals (SET CHRONO 1-2-3-4)
Below are given the steps for accessing the relative menu starting from Stand-By mode.

Press the key “access

menu” to access

the

MENU page

Press the key

“confirm”

to access the

USER page

Press the key

“selection”

to quickly switch to

CRONO-THERMOSTAT.

By pressing the Increment key you can change each value and, at step 3, enable the days of the week;

Press “confirm” to confirm the settings and switch to the next value;

Press the “back” button to return to the CHRONO-THERMOSTAT page.

As per the above example, it has been set as CHRONO 1 an ignition from 08.30 to 21.30 from MONDAY to FRIDAY at the oper

ating power 5 with a room temperature set at 21 ° C. Programmes 2-3-4 can be set in the same manner.

To exit the CHRONO-THERMOSTAT function and return to Stand-by page, press the button repeatedly.

AIR / PELLETS setting

Setting of the PELLET-FLOW mix enables you to immediately change the quantity of pellet loaded in the brazier and the air inflow.

The stove is tested and inspected with DIN PLUS certified pellets. If using another type of pellets or uncertified pellets, fuel may

need adjustment. Usually, the variation involves the FLOW percentage to adjust the input air and, therefore, the combustion; should

the regulation of flow be insufficient, it may be necessary to also change the percentage of PELLET load.
Below are given the steps for accessing the relative menu starting from Stand-By mode.

Press the key “access

menu” to access

the

MENU page

Press the key

“confirm”

to access the

USER page

Press the key

“selection”

to quickly switch to

SET AIR / PELLETS.

As per the above example, you have set a percentage of -2 for PELLETS and +3 for the FLOW

, an indication

that a setting like this is a consequence of the fact that the oxygen needed for combustion is insufficient and pellet

size is smaller than the average size of 2 cm.

To exit the SET AIR - PELLET function and return to Stand-by page, press the button repeatedly.

NOTE: The number indicated during the change of parameters refers only to a percentage value that acts on the default

parameters set on the electronic board (exclusively in the WORK phase). These values should be changed in the event

of poor combustion, due in many cases to the purchase of pellets differing from those used during stove testing.

The first setting allows the activation of the CLIMATE COMFORT function. This function is intended to ensure that the room tem

perature set is maintained steady upon setting the maximum period of “X” minutes (SWITCH-OFF DELA Y: 5 MIN) before switch-ing

to ECO STOP phase. The STOVE maintains this state until the temperature drops below the set value (CLIMATE COMFORT DELTA:

5°C

). For example, with the room temperature at 21 ° C, the stove switches of f when this temperature is reached and restarts when

the temperature reaches 16°C (21°C - 5°C). You can also activate the function using an external thermostat, keeping in mind that this

does not include the value of the hysteresis.

Description of menu functions

Manuale utente PALMARE IDRO TOUCH RADIO

Pag.32

Pag.33

Vers. 01 del 07/04/15

Press the key

“confirm” to

access the

SETUP

SETTINGS

Press the key

“selection” to switch

to the function

VERSION FW.

Press the key

“confirm”

to access the function

To access the next setting, follow the steps given above or simply remove and replace the batteries.

The device resets and prompts you again to select the language you want to set.

Settings > Language

Settings > Adjust

Use the UP/DOWN keys to change the value read by the

room temperature probe installed inside the handheld

set, with respect to a reference value.

The value can vary from -10°C to 10°C.

The standard value is 0°C.

By pressing the following key you will confirm of data

and switch to the page within SETTINGS menu

The stoves equipped with ventilation system can heat the area in which are installed through the heat generated by the window and

the room temperature fan installed inside them.

Below are the messages shown on display when the stove is equipped with ventilation system.

To exit the page and return to Stand-by page, press the button repeatedly.

VENTILATION menu (function only for models in which the same is specified in the dedicate user’s manual)

Control: v

entilation can be set from 0 to AUTO where 0 indicates that the same is disabled, setting from MIN to MAX enables selecting

the heat distribution speed. If set to AUTO, the ventilation follows the power set on the stove.

Press the increase/decrease keys

“increase/decrease”

to change the ventilation.

To exit the page and return to Stand-by page, press the button repeatedly.

The exit key shows the CHRONO menu to set other variables related to the menu functions.

Press the key

“enter” at the end of the

setting, from the following

CHRONO page

The temperature read by the handheld unit controls the modulation of the stove. If you want to adjust the ventilation by

adjusting the stove, set the fan to A mode as shown in the relative chapter.

Press the key

“access menu” to

access the

MENU page

Press the key

“confirm”

to access the

USER page

Press the key

“confirm”

to quickly switch to

VENTILATION.

Press the increase/decrease keys

“increase/decrease”

to change the ventilation.

Pages displayed upon the activation of advanced layouts

By activating a layout different from the standard (layout 0), even if maintaining the same functions of the menu, the “Stand-by” page will

display all connected utilities such as the temperature of the boiler of the puffer.

Below is shown the new display mode and the function of every icon for every layout, to change the various settings.

Layout 1 (DHW heating control)

The following layout can be used when you have a boiler that is not equipped with plate heat exchanger and you intend to buy a puffer

that should be connected to the circuit to produce hot domestic water.

In this type of circuit, room temperature is controlled however by the handheld unit which, being a radio device, acts as a remote

chronothermostat. The boiler is managed by the thermostove through a contact or immersion probe (not supplied) connected directly

to the back of the stove. Below is shown the new “Stand-by” mode.

By setting the SUMMER function, the 3-way valve remains fixed in a single position, enabling the release of heat output

by the stove exclusively inside the boiler. As soon as this condition is reached, the boiler switches to ECO STOP mode.

The operation is the same as for the basic layout except for the fact that in this layout, the boiler exchanges heat directly in the

boiler (priority); when the temperature set is reached, the 3-way valve changes its position and the boiler starts exchanging heat within

the heating circuit. From this moment, the stove is controlled by the radio handheld unit for contolling the room

temperature or via H2 setting (see the operation with layout 0 to find the data on modulation, eco stop etc.).

The 3-way valve is directed again into the boiler when:

- there is a request from the Boiler;

- there is a requested from the flow switch (optional, if connected).

The stove restarts from Eco-stop or Stand by mode according to heating requests or boiler requests.

T°C Boiler

From STAND BY mode, press

the ARROW key UP

to set the

room T°C

and DHW boiler T°C that you

desire.

Boiler water T°C

From STAND BY mode, press

the ARROW key DOWN

to set

the boiler water T°C

that you desire.

Press the key

“V” from STAND BY page

to display the actuale states and

the room temperature

Chrono function

By enabling the chrono function, it is possible to control the ventilation speed for each program as shown in the logic above.

Press the key

“access menu” to

access the

MENU page

Press the key

“confirm”

to access the

USER page

Press the key

several times

to quickly switch to

CRONO-THERMOSTAT.

If the type of system designed requires controlling the 3-way valve (diagram 1 and 3), it is necessary to purchase the

optional kit from the retailer or the authorized Ravelli dealer.

DATE-TIME

ENABLE EXT. T

SEASON

CONTRAST

FW VERSION

LANGUAGE

ADJUST

MENU

USER

TECHNICIAN

VENTILATION POW.

USER

POWER SETTING

CHRONOTHERMOSTAT

SCREW LOADING

SET AIR-PELLET

MENU

USER

TECHNICIAN

USER

POWER SETTING

SET AIR-PELLET

CHRONOTHERMOSTAT

SCREW LOADING

CHRONO

ENABLE CHRONO

VENTILATION POW.

SET CHRONO 1

SET CHRONO 2

SET CHRONO 3

SET CHRONO 4

POWER MOD

PUMP
3-WAY VALVE HEAT
PRESSURE 1.1 BAR
HH T .

21°C

MANUFACTURER’S