Ravelli Pompeii Owners & Installation Manual Download

Page: 29 / 53

Manuale utente PALMARE IDRO TOUCH RADIO

Pag.36

Pag.37

Vers. 01 del 07/04/15

ANOMALIA

DESCRIZIONE

RD SYSTEM REGULATION

REQUEST

(only if the RDS system is

installed)

It shows that the testing procedure and initial parameter calibration have been completed

incorrectly.

This indication, however, does not block the stove.

FLOW METER FAILURE

(only if the RDS system is

installed)

It shows a failure of the air flow meter and the stove switches to minimum capacity

disabling the RDS system.

SERVICE REQUEST

The threshold value of set work hours has been reached. The symbol displayed remains

active throughout the work phase. Non-routine maintenance is required on the stove.

Warning Pop-Up

PHASE

DESCRIPTION

OFF

The stove is off

WAIT FOR PELLETS

OUT OF

When the switch-on request from ECO-STOP mode coincides with an automatic switch-off

condition (from the TIMER), the stove turns on ensuring total cleaning of the brazier before

switching to FINAL CLEANING.

INFEED SCREW

OVERFLOW

CONDITION: when the pellet setting (set p5) is near the continuous load condition.

SOLUTION: Set the value back to 0.

GENERIC ALARM

The stove is in alarm state; refer to the troubleshooting chapter.

ANOMALY (general)

The stove has detected an anomaly; refer to the troubleshooting chapter.

AUTOMATIC CLEANING

SYSTEM ACTIVE

For models with automatic cleaning system it indicates the operating state of the same.

STAND BY

Forced shutdown state when the boiler water reaches 85°C. The stove restarts automatical-

ly if the restart conditions are met.

REASON

SOLUTION

• The door and the ash box are not closed correctly

• Make sure they are closed properly.

• Poor combustion in grate.

• Switch off the stove, clean the brazier and check the cleanliness of the
support bench, clean the tube bundle by activating the turbolators and adjust
the combustion through pellet/air settings.

• Presence of foreign body in air intake tube.

• Check if present and remove foreign body

• The air flow meter may be dirty.

• Clean the flow meter with the stove in “Switched off” state
• Contact the Support Service

IGNALLING

CLEAN

THE GRATE

(only if the RDS

system is installed

)

Alarms (table with reference codes)

RIAL.

TITLE

REASON

SOLUTION

AL 01 BLACK OUT

- No voltage during work phase

- Press the switch off key and switch on the stove

again
- If the problem persists, contact the Support Service

AL 02 K PROBE FAILURE

- The K probe is malfunctioning

- Contact the Support Service

- The K probe is disconnected from the electronic

board

- Contact the Support Service

AL 03 OVERTEMP. K

- Combustion in the brazier is not optimal due to

clogging or obstructions of internal stove ducts

inside the stove

- Switch off the stove, clean the brazier and the tube

bundle and adjust the combustion setting the Pellet/

Air values

- The tangential fan (if provided) is

malfunctioning or damaged

- Contact the Support Service

- If the problem persists, contact the Support Service

AL 04 FUME EXHAUST DAMAGED

- Fume exhaust encoder is not working or is

connected incorrectly

- Contact the Support Service

- No power to fume extractor.

- Contact the Support Service

- The fume extractor is blocked.

- Contact the Support Service

AL 05 NO SWITCH-ON

- The pellet tank is empty.

- Check for the presence of pellets in the container.

Top up, if necessary.

- Pellet calibration and suction during switch on phase

is incorrect.

- Contact the Support Service

- The ignition coil is faulty or positioned

incorrectly

- Contact the Support Service

AL 06 PELLETS FINISHED

- The pellet tank is empty.

- Check for the presence of pellets in the container.

Top up, if necessary.

- The gear motor is not loading pellets.

- Empty the tank to see if there are any objects inside

that may prevent proper operation of the auger.

- Not enough pellets loaded

- Regulate pellets setting from “SET AIR/PELLETS”
- If the problem persists, contact the Support Service

AL 07 RESETTABLE THERMAL

BREAKER

- The manual reset thermostat connected to the hopper

has been triggered

- Reset the thermostat by pressing the button on the

back of the stove

- Combustion in the brazier is not optimal due to

clogging or obstructions of internal stove ducts inside

the stove

- Switch off the stove, clean the brazier and the tube

bundle and adjust the combustion setting the Pellet/

Air values
• Contacter le Service d’Assistance

AL 08 DEPRESSION

- The flue is blocked.

- Check the flue is free and clean

- The vacuum meter is faulty.

- Check the mains voltage.

AL 12 FUME EXHAUST SYSTEM

FAILURE

- The fume exhaust system has a loss of performance

due to fan obstruction or voltage drop.

- Check the mains voltage.

AL 14 SCREW PHASE

- No cable connection to power the gear motor screw

- Check the mains voltage.

AL 15 SCREW TRIAC

- An internal part of the electronic board that controls

the pellet infeed screw is faulty.

- Check the flue is free and clean

- Possible voltage drops or incorrect input voltage

- Check the mains voltage.

AL 17

NO FLOW

(only if the RDS system is

installed)

- The flow meter does not measure an input air flow

- Check whether the door and the drawer are

properly closed, correctly and check if the air

inlet pipe is obstructed.
- If the problem persists, contact the Support

Service

AL 19

CLEANER FAILURE

(for models equipped with

cleaner)

- The cleaner did not complete the movement

and is not in the correct position

- Reset the alarm and wait for the stove to switch

to SHUTDOWN mode. Cut off and power again,

the system reactivates the cleaner searching the

correct position again.

- If the problem persists, contact the Support Service

AL 10 OVERTEMP. H2O

• The boiler water temperature exceeds 90 °C.

- Check the mains voltage.

AL 11 H2O PROBE FAILURE

• The boiler water probe is malfunctioning.

- Check the mains voltage.

- The boiler water probe is disconnected from the

electronic board.

- Check the mains voltage.

AL16 PRESSURE

• The pressure of the system is greater or lower than a

preset value, allowed values from bar to 2.5 bar. (We

recommend at cold circuit a pressure of about 1.0 bar)

• Fill the system or vent it to bring the pressure

to the value requested for correct operation.

• If the problem persists, contact the Support Service

Adjust RDS

system

The appearance of the message “ADJUST THE RDS SYSTEM” indicates that the initial parameter testing procedure and

calibration has been unsuccessfully. This indication does not block the stove.

Summary of Contents for Pompeii






















































Search results

Summary of Contents for Pompeii

Reviews:

Related manuals for Pompeii

Brands by name

Popular brands

Ravelli Pompeii, Owners & Installation Manual

Search results

Summary of Contents for Pompeii

Reviews:

Related manuals for Pompeii

Brands by name

Popular brands