background image

RAVEN  INDUSTRIES

LIMITED  WARRANTY

WHAT IS COVERED?

This warranty covers all defects in workmanship or materials in your
Raven Flow Control Product under normal use, maintenance, and
service.

HOW LONG IS THE COVERAGE PERIOD?

This warranty coverage runs for 12 months from the purchase date of
your Raven Flow Control Product.  This warranty coverage applies
only to the original owner and is not transferrable.

HOW CAN YOU GET SERVICE?

Bring the defective part, and proof of date of purchase, to your local
dealer.  If your dealer agrees with the warranty claim, he will send the
part, and proof of purchase to his distributor or to Raven for final
approval.

WHAT WILL RAVEN INDUSTRIES DO?

When our inspection proves the warranty claim, we will, at our option,
repair or replace the defective part and pay for return freight.

WHAT DOES THIS WARRANTY NOT COVER?

Raven Industries will not assume any expense or liability for repairs
made outside our plant without written consent.  We are not responsible
for damage to any associated equipment or product and will not be
liable for loss of profit or other special damages.  The obligation of this
warranty is in lieu of all other warranties, expressed or implied, and no
person is authorized to assume for us any liability.  Damages caused by
normal wear and tear, mis-use, abuse, neglect, accident, or improper
installation and maintenance are not covered by this warranty.

Summary of Contents for SCS 660





















































Reviews: