Ray Electric Outboards E2 Repair Manual Download

Page: 14 / 17

Symptoms

3. Will not operate

Cause

1. CF not operating

Correction

1. Check green circuit

in Forward

Control

See "Checking
Circuits"

2. CF normally open
Contacts not making
contact

2. Visually check
contacts. UNPLUG BAT-
TERIES. File contacts
with point file.
Replace contactor, if
necessary.

3. CR normally closed
Contacts not making
contact

3. Same as 2

4. Will not operate

in Reverse

1. CR not operating

1. Check orange circuit.
See "Checking
Control Circuits"

2. CR normally open
Contacts not making
contact

2. Visually check contacts.
UNPLUG POWER TO
MOTOR. File contacts
with point file.
Replace contactor, if
necessary.

3. CF normally closed
Contacts not making
contact.

3. Same as 2

5. Electrolysis --

rapid corrosion on
underwater parts of
motor where paint
is off.

1. Boat grounded to a
battery terminal --
such as through the
base of an automotive
type light. Some
marine running lights
also connected through
base.

1. Eliminate ground by
insulating light from
boat or eliminate
light. NEVER ground
boat when a Ray Out-
board System is
installed.
See Electrolysis

6. Charger will not

1. One or both diodes

1. Check diodes with

charge ("0" ammeter

have failed due to

ohmmeter and replace

Summary of Contents for E2


















Search results

Summary of Contents for E2

Reviews:

Related manuals for E2

Brands by name

Popular brands

Ray Electric Outboards E2, Repair Manual

Search results

Summary of Contents for E2

Reviews:

Related manuals for E2

Brands by name

Popular brands