background image

14

to engine fuel lines and other engine parts.

MIXTURE RATIO IS 40:1

GASOLINE-40PART

OIL-1 PART

Fuel mixture at the rate other than 40:1 may

cause damage to the engine, Ensure mixture

ratio is correct.

FUEL

IMPORTANT

The engine uses two-stroke fuel, a mixture Two-stroke fuel may separate. Shake fuel

of gasoline and 2-stroke lubricant 40:1

container thoroughly before each use. Stored

fuel ages. Do not mix more fuel than you

expect to use within a month.

GASOLINE

Use branded 89 octane or higher unleaded

gasoline known to be of good quality.

FUEL AND OIL MIXTURE

STORING FUEL

Store fuel only in a clean, safe, approved

Inspect fuel tank making sure that it is

container. Check and follow local

clean and fill with fresh fuel. Use a mixture

ordinances. on type and location of

of 40:1

storage container.

PREPARING FOR OPERATIONS

WHEN MIXING GASOLINE WITH TWO CYCLE ENGINE OIL, USE

ONLY GASOLINE WHICH CONTAINS NO ETHANOL OR METHANOL

(TYPES OF ALCOHOL). THIS WILL HELP TO A VOID POSSIBLE

DAMAGE TO ENGINE FUEL LINES AND OTHER ENGINE PARTS.

DO NOT MIX GASOLINE AND OIL DIRECTLY IN THE ENGINE FUEL

TANK.

IMPORTANT: Failure to follow proper fuel mix instructions may cause

damage to the engine.

Summary of Contents for RAY25PB
























Reviews: