manualshive.com logo in svg

RAYLASE SS-II, Manual

The RAYLASE SS-II user manual is a comprehensive manual that provides detailed instructions for operating and maximizing the performance of this advanced product. Download the free manual from our website to unleash the full potential of RAYLASE SS-II and enhance your work efficiency.

Share
Download
background image

Technical data 

Chapter 3 

3.1.2 

Detailed Description 

With the detailed description on the rating plate, the mirror material, the type of cooling, the 
size of the aperture, the type of tuning, the type of connector can be determined. If the scan 
head is a customized one then the detailed description contains the individual customer num-
ber (DKdNr). 

 

 

Mirror material 

BE = Beryllium 
BA = Beryllium/Alu 
OG = Optical Glass 
QU = Quarz 
SI = Silicium 
SC = SiliciumCarbid 
ZS = Zinkselenid 

│ 

│  

Mechanical design 

│

 

│  

Cooling 

│  [N]       = no cooling  

│  [W]       = water cooling 

│  [W2]      = water cooling with 90° angle 

│  [A]       = air-cooled 

│  [WA]      = water cooling and air cooling for mirrors 

│  [W2A]     = water cooling with 90° angle and air cooling for mirrors 

│ 

│  Other mechanical design 

│  [L]       = Head with a lager input aperture for LTM 

│  [10]      = Field size(at AS in cm)Examples: F10… 100m × 100mm; F12… 120m × 120mm; etc. 

│  [M]       = motorization in LTM 

│  [P]       = Laser pointer 

│  [C]       = Camera adapter 

│  [D]       = Dust protection     

│  │      

│  │     

Tuning 

│  │     LN  = low Noise  

│  │     RA  = short acceleration time  

│  │     ST  = minimal step time 

│  │     VC  = vector  

│  │     ML  = multiple tuning (default: LN)  

│  │     MR  = multiple tuning (default: RA)  

│  │     MS  = multiple tuning (default: ST) 

│  │     │   

│  │     │  

Connector

 

│  │     │  D1 = 25pin D-Sub-connector 

│  │     │  D2 = 25pin D-Sub-con 9pin D-Sub-connector 

│  │     │  DF = D-Sub for FOCUSSHIFTER 

│  │     │  A1 = 25-pin D-Sub-connector 

│  │     │  A2 = 25-pin D-Sub-co  9-pin  D-Sub-connector 

│  │     │  E2 =  6-pin  Epic-co 17-pin  Epic-connector 

│  │     │  E3 =  6-pin  Epic-co 17-pin  Epic-co M12 circular connector 

│  │     │  E4 =  6-pin  Epic-co 17-pin  Epic-co M8 circular connector 

│  │     │  E5 =  6-pin  Epic-co 17-pin  Epic-co M8 + M12 circular connector 

│  │     │  │ 

│  │     │  │  

Navision customer number 

└─ └──── └─ └─ └──── 
SS-[MMM]-TT-CC/DKdNr 

3.2 

Conformity with directives 

The deflection unit conforms to the requirements of the following directives: 

  EU Directive 2004/108/EC (EMC) 

  WEEE Directive 2012/19/EC 

RoHS II 2011/65/EU 

  Directive 2006/42/EC on machinery 

  For details of conformity with other directives, contact RAYLASE. 

 

 MN065_v1.0.1 

2-Axis Laser Beam Deflection Unit SS-II 

13 

Summary of Contents for SS-II



























Reviews:

No comments

Related manuals for SS-II

Brands by name

Popular brands

Load more brands