background image

Chapter 6 

Cleaning 

20 

RAYLASE 2-Axis Laser Beam Deflection Units 

MN051_v1.0.5 

ing thorium is enclosed between non-radioactive layers, there is no risk to the user under 
normal circumstances.  

 

Damage to zinc selenide optical elements 

Under normal circumstances, no special precautions are necessary when handling or storing 
zinc selenide.  

In case of damage to a zinc selenide optical element or its anti-reflex coating, follow the in-
structions below.  

 

Damage to anti-reflex coating 

  Possible causes: 

Coating coming into contact with water, acids or alkalis 

Mechanical damage due to improper cleaning or handling 

  Action: 

Pack the optical elements in an airtight sealed plastic container. 

Return the container to your supplier. The supplier is responsible for professional 
disposal of the material. 

 

Damage to optical element 

  Possible causes: 

Contact with water, acid or alkali 

Mechanical damage due to improper cleaning or handling 

  Action: 

Avoid inhaling dust! 

Carefully collect up fragments and pack them in an airtight sealed plastic container. 

Return the container to your supplier. The supplier is responsible for professional 
disposal of the material. 

 

Damage to optical element due to laser radiation 

  Cause:  

Damage to optical element due to laser radiation (laser radiation is no longer 
completely transmitted but is absorbed into the element due to damage to the anti-
reflex coating or contamination of the optical element) 

  Action: 

Switch off the laser device immediately! 

Leave the room for at least 30 minutes! 

Wear gloves and a mouth protector while performing the subsequent steps! 

Carefully collect up all fragments and pack them in an airtight sealed plastic container. 

Clean all contaminated components and surfaces with a damp cloth and pack the 
cleaning cloths in a sealed plastic container.  

Return the containers to your supplier. The supplier is responsible for professional 
disposal of the material. 

 

Warning: 

Because of the risks outlined, zinc selenide optical elements must be cleaned with 

special care and is performed entirely at your own risk!

 

Summary of Contents for SUPERSCAN II-10



























Reviews: