Note:
The MFD shallow depth alarm is independent of the Shallow
depth alarm available on instrument displays. If you have Instrument
displays connected to your system it is recommended that their shallow
depth alarms are disabled.
•
[Position drift]
— If enabled, an Alarm is triggered when your vessel drifts
from its current GNSS (GPS) position by more than the specified
[Drift
range]
.
•
[Anchor drag]
— When the Anchor drag alarm has been configured and
activated in the Chart app the Anchor drag alarms can be turned off by
selecting
[Raise anchor]
•
[Low fuel remaining]
— If enabled, an alarm is triggered when the fuel
remaining in your fuel tanks reaches the specified
[Fuel level]
.
Note:
The Fuel manager must be enabled for alarms to be triggered.
•
[LightHouse chart obstructions]
, If enabled, an alarm in
triggered when an obstruction is detected. For details refer to:
p.193 — Obstruction alarm (legacy LightHouse charts)
•
[DSC alarms]
— If enabled, an alarm is triggered when DSC distress calls
are received.
•
[AIS safety messages]
— If enabled, an alarm is triggered when AIS safety
messages are received.
•
[MOB data type]
— Determines whether the MOB waypoint is fixed at the
[Position]
the alarm was triggered, or advances its position based on tide
and wind effects (
[Dead reckoning]
).
•
[Fishing range]
— If enabled, an alarm is triggered when your Depth
reading reaches the depth specified in
[Shallow water arrival]
or
[Deep
water arrival]
.
•
[Water temperature alarm]
— If enabled, an alarm is triggered when the
water temperature reading reaches the temperature specified in
[Lower
temp limit]
or
[Upper temp limit]
.
•
[Digital switching alarms]
— When your system includes digital switching
a list of all configured digital switching alarms will be displayed. If your
system includes a YachtSense ™ Link router then the router’s alarms will
be displayed.
– For details of digital switching alarms refer to:
p.113 — Digital switching alarms
– For details of YachtSense ™ Link router alarms refer to:
p.113 — YachtSense Link router alarms
•
[AX8 camera messages]
— If enabled, messages from a connected AX8
camera will be presented as alarms on your MFD.
•
[Engine alarms]
— If enabled, alarms will be triggered when engine warning
alarms are received from connected, compatible engine management
systems or interfaces.
•
[Generator alarms]
— If enabled, Alarms raised by compatible generators
will be displayed on the MFD.
•
[Apps and connected devices]
— Select
[Configure]
— Select
to enable and disable alerts received from partner integration
hardware or apps. For details on partner integrations refer to:
p.438 — Partner Integration and third-party apps
•
[Battery alarms]
— Select
[Configure]
to view the battery configuration
page where you can set alarms for each detected battery. For details refer
to:
•
[Minimum sonar depth]
— When your sonar transducer detects depths of
0.8 m/2.62 ft the alarm is triggered.
Important:
Accurate bottom tracking can be unreliable in depths
shallower than 0.8 m/2.62 ft. When operating at or below this depth be
cautious of misleading sonar returns or false bottom tracking.
•
[Home button active alarm indicator]
— If enabled, when an alarm is active
the onscreen home icon is colored red and contains a warning triangle.
7.4 External alarm speaker / buzzer
If your MFD has a built-in buzzer or is connected to a wired external buzzer,
MFD alarms will trigger an audible tone. If you connect your MFD to a
Bluetooth speaker then the alarm tone can also be heard from the speaker.
When connected to a Bluetooth speaker, a separate volume control is
available to control the volume of MFD Alarms sounded through the speaker.
For more information, refer to:
p.71 — Bluetooth speaker pairing
112
Summary of Contents for LIGHTHOUSE 4
