background image

ABOUT YOUR WATER HEATER 

 

TO TURN ON THE WATER HEATER 

 WARNING!

 If you smell gas do not attempt to turn on the water heater. 

 

Fill the system with water 

(refer to “

To Fill the Water Heater

” on page 28) 

 

Open the gas isolation valve fully at the inlet to the water heater. 

 

Plug in the power supply cord at the power outlet. 

 

Switch on the electrical supply at the power outlet to the water heater. 

NOTE

: If the water heater is correctly installed, this will also activate the circulating pump. 

The water heater will operate automatically when a call for heat occurs. 

HOW DO I KNOW IF THE WATER HEATER IS INSTALLED CORRECTLY? 

Installation requirements are shown on 

pages 

11 

to 

16. The water heater must be installed: 

 

by a qualified person, and 

 

in accordance with the installation instructions, and 

 

in  compliance  with  Standards  AS/NZS 3500.4,  AS 5601  or  AS/NZS 5601.1,  as  applicable  under  local 
regulations, and all local codes and regulatory authority requirements. 

In New Zealand, the installation must also conform with NZS 5261, as applicable under local regulations, and the 
New Zealand Building Code. 
 

DOES THE WATER CHEMISTRY AFFECT THE WATER HEATER? 

The water heater is suitable for most public water supplies, however some water chemistries may have detrimental 
effects on the water heater, its components and fittings. Refer to 

“Water Supplies”

 on page 35. 

 
If  you  are  in  a  known  harsh  water  area  or  you  are  not  sure  of  your  water  chemistry,  have  your  water  checked 
against the conditions 

described on pages

 35. 

 

HOW LONG WILL THE WATER HEATER LAST? 

The water heater is supported by a manufacturer‟s warranty 

(refer to page 

39

)

. There are a number of factors that 

will  affect  the  length  of  service  the  water  heater  will  provide.  These  include  but  are  not  limited  to  the  water 
chemistry,  the  water  pressure,  the  water  temperature  (inlet  and  outlet)  and  the  water  usage  pattern.  Refer  to 

“Precautions”

 on page 6. 

 

PRECAUTIONS 

Where damage to property can occur in the event of the water heater leaking, the water heater must be installed in 
a  safe  tray.  Construction,  installation  and  draining  of  a  safe  tray  must  comply  with  AS/NZS 3500.4  and  all  local 
codes and regulatory authority requirements. 
 
The water heater mu

st be maintained in accordance with the Owner‟s Guide and Installation Instructions. Refer to 

“Regular Care”

 on page 10. 

 
If  this  water  heater  is  to  be  used  where  an  uninterrupted  hot  water  supply  is  necessary  for  your  application  or 
business  you  should  ensure  that  you  have  back  up  redundancy  within  the  hot  water  system  design.  This  should 
ensure  the  continuity  of  hot  water  supply  in  the  event  that  this  water  heater  were  to  become  inoperable  for  any 
reason.  We  recommend  you  seek  advice  from  your  plumber  or  specifier  about  your  needs  and  building  back  up 
redundancy into your hot water supply system. 
 

SERVICING 

For  safe  and  efficient  operation,  the  water  heater  should  be  serviced  annually  by  your  nearest  Rheem  Service 
Department  or  their  Accredited  Service  Agent.  Only  genuine  replacement  parts  should  be  used  on  this  water 
heater. 

Refer to “

Service Procedures

” on page 34 

 WARNING:

 Servicing of a gas water heater should only be carried out by qualified personnel. 

 

Summary of Contents for B0200









































Reviews: