Compass
Installation and Service manual
STD 22
Compass STD 22
Compass STD 22 Compact
I
Edition: Sept. 13, 2005
3646/110--233.DOC010302
CONTENTS
Page
Declaration of Conformity
Safety notes
1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
General information
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
CAN bus (CAN = Controller Area Network)
13
. . . . . . . . . . . . . . . . . . .
2
Preparing to install the STD 22 Compact Gyro Compass
15
. . . .
2.1
STD 22 Compact Compass – Scope of Supply
15
. . . . . . . . . . . . . . . .
2.2
General information concerning installation
of the STD 22 Compact Compass
16
. . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Creating cable connections
17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
General information concerning on-board wiring
17
. . . . . . . . . . . . . . .
2.3.1.1
General information about creating an earth connection
20
. . . . . . . .
2.4
Installing the compass and putting it into operation
21
. . . . . . . . . . . . .
2.4.1
Remove the transportation support with outer sphere,
supporting liquid and distilled water.
21
. . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1
Assembling the compass enclosure
22
. . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2
Installation of the gyrosphere
25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.3
Filling with distilled water and supporting liquid
27
. . . . . . . . . . . . . . . .
2.4.1.4
Inserting the outer sphere in the compass enclosure
29
. . . . . . . . . . .
2.5
Creating cable connections and plug connections
31
. . . . . . . . . . . . . .
2.5.1
Overview of plug connections and fuses on PCB‘s
31
. . . . . . . . . . . . .
2.5.1.1
Connecting the course receiver
in the STD 22 Compact Gyro Compass
33
. . . . . . . . . . . . . . . . . . . . . . .
2.5.1.2
Connecting status and control signal outputs
in the STD 22 Compact Gyro Compass
35
. . . . . . . . . . . . . . . . . . . . . . .
2.5.1.3
Connecting signal inputs for QS and SEC
in the STD 22 Compact Gyro compass
37
. . . . . . . . . . . . . . . . . . . . . . .
2.5.1.4
Connecting the power supply cable
39
. . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.1.5
Connecting the compass to earth
40
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6
Installation and commissioning of optional features
41
. . . . . . . . . . . .
2.6.1
Installation and commissioning of
the Additional Output Box 143--103
41
. . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.2
Installation and commissioning of the AC/DC Converter 121--062
43
2.6.3
Installation and commissioning
of the Operator Unit Quick Settling (QS) 130--606
46
. . . . . . . . . . . . . .
2.6.3.1
Installing the Operator Unit Quick Settling
47
. . . . . . . . . . . . . . . . . . . .
2.6.4
Switching on, settling and adjustment
49
. . . . . . . . . . . . . . . . . . . . . . . .
2.6.4.1
Switching on the compass
49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.4.2
Checks on the compass
49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.4.3
Setting the STD 22 Compact Compass into operation
51
. . . . . . . . . .
2.6.4.4
Setting the compass zero (reference course)
53
. . . . . . . . . . . . . . . . .
2.6.4.5
Reading the alignment error
55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.4.6
Setting Channel 1 and Channel 2
56
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.4.7
Setting the information source for Speed Error Correction
59
. . . . . . .
2.6.4.8
Adjustment of essential operating modes
63
. . . . . . . . . . . . . . . . . . . . .
2.6.4.9
Function check on externally connected course receivers
70
. . . . . . .
