background image

1/20/2015 (3:46 PM) 
2034vx & 2034vxa v6.0.doc 

 

 

 

4”

Bag should

rest on the

floor.

 

 

2.9

 

  Electrical Connection

 

2.9.1

 

  Plug cabinet into a grounded 110-120 volt 

electrical outlet with 15-amp circuit breaker.

 

2.9.2

 

.

 

Turn on power-switch to test proper function 

of motor and lights 

2.9.3

 

  Check plastic dust bag and make sure it is 

collapsing when the dust collector is on. 
 

2.10

 

  Exhaust Connection

 

2.10.1

 

  

The exhaust blower is fitted with a sheet 

metal elbow for the purpose of directing the exhaust 
in an upward direction. Installation of an exhaust 
vent is optional for the purpose of reducing noise or 
exhausting dusts resulting from damaged or worn 
dust bags.  Installation of exhaust vent should be 
done by a licensed contractor to make sure there is 
no restriction of airflow that would affect the proper 
function of the dust collector. Exhausting through a 
long vent pipe may require an additional exhaust 
fan installed at the point the vent exits the building.

 

 

 

2.11

 

  Adding Abrasive Media

 

The system has been shipped without the abrasive 
media in the pot. Turn the dust collector on, place 
unopened 50lb bag of 150 grit aluminum oxide 
abrasive into the cabinet.  Slit the center of the bag 
open. Close the side door and empty the bag using 
the front armhole access.  After the dust has cleared 
remove the bag from the cabinet. 

! NOTICE 

The abrasive media will break down over time 
causing more dust in the cabinet and slower 
blasting. New abrasive should never be added to old 
abrasive. Instructions for removing worn abrasive 
and adding new abrasive are covered in the 
Operation Manual. DO NOT over fill the pot with 
more than 50 lbs of abrasive; this may prevent the 
pot closure cap from sealing.

 

2.12

 

  Air Compressor Requirements

 

NOTE: Customer Supplied and used only 
for the Cabinet.

 

The following or similar items are recommended 
for moderate cabinet use.  www.grainger.com or 
call 800 225 5994 
  

1. Air Compressor

 

Grainger’s Model: # 4YN50 
2 horsepower, High Performance Cast Iron Air 
Compressor 
Free Air CFM @ 90 PSI: 5.5  
Free Air CFM @ 135 PSI: 4.9 
Volts 60 Hz: 115/230 
Amps: 15/7.5  
Tank Capacity (Gal): 26 
 

2. Water Trap

 

 

3. Air hose

 

 
 

 
 
 

Summary of Contents for 2034vx





















Reviews: