background image

13

REPAIR AND MAINTENANCE

 Cleaning

Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents, as they may damage the 

surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners, as they may damage or dissolve the plastic 

components or soften the decals or decal adhesive.

 Wheels and Bearings

Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless, 

it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for 

proper tightness, bearings for side-to-side play, and for loose parts. When a wheel develops play, this is an indication 

of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn, tires, 

wheels/bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other 

than genuine Razor wheels may not be compatible with your DXT. The use of anything other than genuine Razor 

replacement parts may affect your safety and will void your warranty.

 Replacement Parts

 

The most frequently requested replacement parts are available for purchase at some Razor retail partners.  

For the complete selection of replacement parts visit shop.razor.com.

 Service Centers

 

For a list of authorized Razor service centers:  

• Check online at www.razor.com. 

• Additional Customer Service contact information is listed at the back of this manual.

Summary of Contents for DXT

















Reviews: